|
msanborn
|
 |
« on: January 19, 2013, 08:41:40 pm » |
|
Does anyone have a 4 wire switch available for sale? Getting ready to re-assemble a 81, and thats the part I am lacking. Thanks.
|
|
|
|
|
Logged
|
Vendo 81
Vendo 39
Pepsi VMC 81
Ideal Slider
Glasco Slider
|
|
|
|
TheGarbageHunter
|
|
« Reply #1 on: January 19, 2013, 10:14:00 pm » |
|
Hmmm, which machines use them. Any of the square tops?
|
|
|
|
« Last Edit: January 19, 2013, 10:58:39 pm by johnieG »
|
Logged
|
Garbage Gold Hunter
|
|
|
|
Jonathan816
|
|
« Reply #2 on: January 21, 2013, 08:53:56 am » |
|
If you can't find one, you could replace the ballast which would allow 2 wire push buttons I believe.
|
|
|
|
|
Logged
|
VMC 81 - Pepsi
VMC 110 - Pepsi
|
|
|
|
MoonDawg
|
|
« Reply #3 on: January 21, 2013, 10:03:45 am » |
|
If you can't find one, you could replace the ballast which would allow 2 wire push buttons I believe.
It's probably a good idea to just plan this into a restoration, since the ballast is in such a hard to reach location. |
|
|
|
|
Logged
|
Glen
|
|
|
|
msanborn
|
|
« Reply #4 on: January 25, 2013, 03:36:31 am » |
|
I definitely will replace the ballast, not an option in this case, does anyone have the wiring diagram for a 2 wire switch, versus the 4 wire option? Tks M
|
|
|
|
|
Logged
|
Vendo 81
Vendo 39
Pepsi VMC 81
Ideal Slider
Glasco Slider
|
|
|
|
SIGNGUY
|
|
« Reply #5 on: January 25, 2013, 10:10:24 am » |
|
Good discussion as i just ran out of my last 4 wire switch as well and now am faced with replacing ballast and switch.
I know that Funtronics sells the ballast ,but didn't see the swithc, ,is it just any old 2 wire switch that I can pick up at Home Depot ? and how does the wiring work .. a diagram would be excellent since it will be different.
Thanks
John
|
|
|
|
|
Logged
|
Soda Machine Enthusiast since 1996!
|
|
|
|
johnieG
|
|
« Reply #6 on: January 25, 2013, 11:40:40 am » |
|
I covered this before {converting from a 4-wire (push to start/pre-heat type) to a 2-wire (instant-start), but I see that the diagram is gone (like all of the other early post pictures) I'll seen if I have another diagram on my old IDE "drive in a can" (external IDE hard-drive case) from back then...
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
msanborn
|
|
« Reply #7 on: January 26, 2013, 06:59:51 am » |
|
Thanks
|
|
|
|
|
Logged
|
Vendo 81
Vendo 39
Pepsi VMC 81
Ideal Slider
Glasco Slider
|
|
|
|
johnieG
|
|
« Reply #8 on: January 26, 2013, 12:19:02 pm » |
|
here's a basic instant start ballast diagram
|
|
|
|
« Last Edit: January 26, 2013, 12:40:30 pm by johnieG »
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
johnieG
|
|
« Reply #9 on: January 26, 2013, 12:39:44 pm » |
|
Now compare it to this pre-heat circuit diagram
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
