|
pinballdude
|
 |
« on: August 02, 2009, 07:38:08 pm » |
|
Scored a Glasco Coca-Cola cup Fountain dispenser, countertop.
There are no serial/model/manufacture plate on it.
It does have the Glasco logo on the front near the drain pan.
There are 4 tap handles, I would like to find a Sprite and a TaB
sticker to place on the tap handles. Would need to be early 60s vintage and
have a protective coating. The stickers are 3/4 inch high and 1-1/2 inches wide.
Two of the tap handles are not attached to the inside of the machine. I see no
way to remove sides, back or bottom to attach something to hold the handles
on. They just slide out. I hope that I can power the light behind the logo by
by-passing the compressor. I would like to use the unit as a display piece
not necessarily a functional unit.
Photos later.
Terry
|
|
|
|
« Last Edit: August 08, 2009, 11:02:10 am by pinballdude »
|
Logged
|
|
|
|
|
pinballdude
|
|
« Reply #1 on: August 08, 2009, 11:03:26 am » |
|
My Son Finally Got THe Pictures Done-
|
|
|
|
|
Logged
|
|
|
|
|
pinballdude
|
|
« Reply #2 on: August 08, 2009, 11:05:24 am » |
|
 Looking For Labels For These Tap Handles. Need A TAB And A SPRITE.
|
|
|
|
|
Logged
|
|
|
|
|
pinballdude
|
|
« Reply #3 on: August 22, 2009, 02:10:49 pm » |
|
So, does ANYBODY have any experience with one of these?
Two of the tap handles are not anchored to the back of where
they are put in. I cannot see ANY where to get inside of this machine
If I lift up the side panels, I just see a solid wall. There is no way in
from below. I can see something inside when I remove one of the tap handles
and shine a flashlight in.I don't really want to get the machine running, just
displayable. I have the light behind the logo working I just need to figure
out how 2 handles are loose and 2 are not.
Thanks.
Terry
|
|
|
|
|
Logged
|
|
|
|
|
Jim
|
|
« Reply #4 on: August 22, 2009, 02:54:31 pm » |
|
Terry,
Glad you got the light working!
As far as the dispensing handles are concerned, I cannot advise as I have not dealt with taking this type of dispenser apart...
Hopefully, someone might have experience and chime in...
|
|
|
|
|
Logged
|
My six cents, Jim  |
|
|
|
pinballdude
|
|
« Reply #5 on: August 22, 2009, 09:56:44 pm » |
|
On a slightly different note...
Know which model machine has the matching
lime green/turquoise blue/white rounded diamonds
around the logo?
I have a clock that matches this particular Coca-Cola
logo and someday like to find the machine that goes with it.
Hopefully it is a small machine!
Terry
|
|
|
|
|
Logged
|
|
|
|
|
loman4ec
|
|
« Reply #6 on: August 23, 2009, 01:03:14 am » |
|
The sign is called a "StyleStar" Sign. It was a common sign used in the mid to late 60's. I have personally only seen Cavalier 64's with this sign. They come around quite often. Here is a picture of one that I had a while ago. It is about as small as you can get.
|
|
|
|
|
Logged
|
|
|
|
|
pinballdude
|
|
« Reply #7 on: August 23, 2009, 07:54:59 pm » |
|
I REALLY like that one!! It matches the fountain dispenser
as the logo *sticks out* away from the machine and had the plastic
cover much like the dispenser.
I may have to look for one of those. I'll have to learn to
live with the woodgrain, eh?
Terry
|
|
|
|
|
Logged
|
|
|
|
|
Ltransam
|
|
« Reply #8 on: August 23, 2009, 08:59:03 pm » |
|
Terry Pinballdude  Check e-bay Item Number 270446670783 I beleive ITs just what you Need .. First Time I seen a Dixie Narco with the StyleStar .As Josh said You Mainly see them on Vendo 64 & I'v even seen the sign in a couple C-96 Squire Tops Ltransam |
|
|
|
|
Logged
|
Glascock Counter Top
VMC 81 7Up
Vendo-110-81D-V-56 V-23
Jacobs Pepsi-56
Stoner Cookie &5 Pull Pastry& 180 Candy
Kelvinator FS-51(Canada)
Cavalier's C-55-E-C-55-D
Selmix Sprite
Selmix Pepsi on Draugh
|
|
|
|
pinballdude
|
|
« Reply #9 on: August 23, 2009, 10:26:37 pm » |
|
I see several Stylestar machines listed under Glasco (DUH!)
Several pre-mix (cup) machines, several bottle and a few can machines.
Will watch for one local. Hope to find a small one. mybe someone will be interested in my Cavalier?
I gotta go outside to find the model # if anyone is interested.
Terry
|
|
|
|
|
Logged
|
|
|
|
|
