|
Slapshot42
|
 |
« Reply #10 on: November 27, 2019, 09:47:17 pm » |
|
Nope, just the two-lead model, the replacement compressor harness has an accessory connector that supplies line voltage ( not switched) it’s just not show in my state of the art drawing...  I just tapped onto that & wired it into the upper terminal strip to supply line voltage to the vending & sold-out circuit. Yep that’s the pileup I remember!  Jeeze, they always look so cute & innocent on the surface, ( just like kids  ). Since mine is removed can I use a 3 lead like a 81 door light to power the terminal board ? I have bought both suppliers wiring harnesses . SJW ( EP15 ) one comes with (2) leads t stat and , evap fan. Usually have to open the trap door in the back at add a 16 gauge wire with ring terminals for hot wire. FunTronics wiring harness comes with about 3” of wire with a weird round plug. I usually cut that off and add spade terminals for a hot wire. Thanks for the help!! |
|
|
|
« Last Edit: November 27, 2019, 09:55:16 pm by Slapshot42 »
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #11 on: November 28, 2019, 11:31:48 am » |
|
Either type of power harness will work, I just prefer the Dixie-Narco molded rubber style, btw the weird little round connector is called a “Lyall” plug ( pronounced “lie-all”) they come in two and three pin models, they are quite common on large commercial coolers, where many fan motors come pre-wired with it ( the Lyall plug) as a disconnect means to make servicing to change them out easier where you’d have many of them say in a grocery store, etc. And now you know more than you’d ever want to know about Lyall plugs. |
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
Slapshot42
|
|
« Reply #12 on: November 28, 2019, 12:01:23 pm » |
|
Is the Dixie Narco style from SJW or do you have a different supplier ? Thx
|
|
|
|
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #13 on: November 28, 2019, 12:57:40 pm » |
|
I buy mine locally, but yes, it’s the same.
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
Slapshot42
|
|
« Reply #14 on: November 30, 2019, 08:53:39 pm » |
|
After cleaning the original junction box the HP rating is 1/8 hp. Also looking for a replacement fan blade as mine is broken. I measured it at at 6” wide . It resembles the fan below the pre-cool shelf of the VMC 33 .
|
|
|
|
« Last Edit: November 30, 2019, 09:01:18 pm by Slapshot42 »
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #15 on: November 30, 2019, 09:28:26 pm » |
|
Hmmm mine said 1/5, but the 3-in-1 mentioned earlier in the thread has a range from 1/12 to 1/5HP so you should be good, that’s a very early version of a tri-blade fan. They are prone to cracking were the blades meet the deep-drawn hub.
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
Slapshot42
|
|
« Reply #16 on: November 30, 2019, 09:37:38 pm » |
|
Agreed the serial tag was worn with no number . Thought it was worth putting the actual HP rating down for reference.
Now to find a fan blade ...
|
|
|
|
« Last Edit: November 30, 2019, 09:39:10 pm by Slapshot42 »
|
Logged
|
|
|
|
|
Slapshot42
|
|
« Reply #17 on: December 01, 2019, 11:40:45 pm » |
|
New 3 - 1 - how did you get ring terminals to fit in the threads of those terminals ? There is small channel for the wire to go through my ring terminal shoulder / collar is to long to find inside there . I tried bare wire with a loop and it starts up just not sure good of connection I’m getting . I’ve seen some people tin solder the wire .
|
|
|
|
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #18 on: December 02, 2019, 11:54:01 am » |
|
Don’t know about your compressor model, but mine had phenolic plastic binding post terminals , I just removed the phenolic caps & replaced them with 10-24 nuts & some washers.
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
|
|
