Kerosen
Newbie
 Offline
Posts: 17
Have a Coke
|
 |
« on: February 17, 2014, 07:57:25 pm » |
|
Hi everybody, i have a Coinco S300E9400 with a problem, the Canadian change (quarter-nickle-dime) just passthru
no problem with the American change only with the Canadian
any advise for me to fix the problem
and any place where i can find the manual
Thank you
|
|
|
|
|
Logged
|
Cavalier uss-8-64
Cavalier uss-12-96
Cornelius compact 50
|
|
|
|
tkaz
|
|
« Reply #1 on: February 17, 2014, 08:19:25 pm » |
|
Not sure if there is a manual out there for it. Sounds like the problem is in the slug rejector, the top section of the mechanism, is there any number on that, like Coinco 880? A picture would help if you can get one.
|
|
|
|
|
Logged
|
|
|
|
Kerosen
Newbie
Offline
Posts: 17
Have a Coke
|
|
« Reply #2 on: February 17, 2014, 09:15:30 pm » |
|
Yes it's a Coinco 880
|
|
|
|
|
Logged
|
Cavalier uss-8-64
Cavalier uss-12-96
Cornelius compact 50
|
|
|
|
tkaz
|
|
« Reply #3 on: February 18, 2014, 11:30:25 am » |
|
Take the two tabs that are on the top corners, lift them up and pull the slug rejector out/forward. Can you post another pic of what is behind that? There should be a set of DIP switches that would control price and a few other options.
|
|
|
|
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #4 on: February 18, 2014, 01:12:59 pm » |
|
Yes, this coinmech has an electronic "slug" rejector, ( some old timers called it the "flight-deck) it uses a simple tuned-metal detection circuit that can determine the correct metal content of the acceptable coins within it's programed range, it also has some small led path detectors that help it determine the diameter of the coins.
Many 'mechs of this type often have a small dipswitchs that will allow or reject Canadian coins. another similar mech is the MARS 9600 series, which is programmable for both or it can even be setup to accept tokens or other non-USA coinage.
Looks like your in need of a manual at this point.
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
Kerosen
Newbie
Offline
Posts: 17
Have a Coke
|
|
« Reply #5 on: February 18, 2014, 01:25:41 pm » |
|
The dipswitch behind are for the accept ou reject of DOLLAR
The dipswitch for the price are on the other pic
|
|
|
|
« Last Edit: February 18, 2014, 01:28:07 pm by Kerosen »
|
Logged
|
Cavalier uss-8-64
Cavalier uss-12-96
Cornelius compact 50
|
|
|
|
tkaz
|
|
« Reply #6 on: February 18, 2014, 01:44:20 pm » |
|
The right side of the slug rejector DIP switches controls US/CAN or US Only coins, have you tried toggling that to see if it'll work (even though it looks like its right)?
|
|
|
|
« Last Edit: February 18, 2014, 01:57:32 pm by tkaz »
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #7 on: February 18, 2014, 10:05:23 pm » |
|
the smaller set of dip switches (on the right hand side as shown) the second switch says "US ONLY" for the lower selection & "US / CAN " for the upper selection...plain & simple.
|
|
|
|
« Last Edit: February 18, 2014, 10:09:25 pm by johnieG »
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
Kerosen
Newbie
Offline
Posts: 17
Have a Coke
|
|
« Reply #8 on: February 19, 2014, 08:26:16 am » |
|
Yes that is the switchs
and they are on the CAN. and it does'n work
the ca. money just passthru
|
|
|
|
|
Logged
|
Cavalier uss-8-64
Cavalier uss-12-96
Cornelius compact 50
|
|
|
|
georgescustompaint
|
|
« Reply #9 on: February 19, 2014, 08:50:43 am » |
|
Are u trying old Canadian coins ? Or new ones ? The new coins won't work as they are Bi Metal and need a conversion kit to work. I believe 2012 coins and up will give u problems.
Not sure where you live, but I deal with a place in Toronto Ontario that can update your mech for you.
|
|
|
|
|
Logged
|
|
|
|
|
