|
|
|
coke_and_stuff
|
 |
« Reply #1 on: September 17, 2006, 04:44:43 am » |
|
Welcome aboard, from the way it looks you have a great starting point. Where are you from?
Joey
|
|
|
|
|
Logged
|
Collector of nice original paint machines
Vendo 81 B, C, D
VMC 81 Pepsi, 7up, RC, Generic
6CV Coke, RC, Pepsi
VMC 110 RC
Vendo 39
Jacobs 26
Mills 47
Selectivend 64 7up NOS
Plus 30-50 parts and project machines
|
|
|
|
dr galaga
|
|
« Reply #2 on: September 17, 2006, 08:11:15 am » |
|
Welcome! Looks like a pretty solid machine there.
Some parts (like the silver trim on the front) you can get from some of the sponsors of this site. Other parts (like the knob) you will probably have to find someone who is parting out a machine. I know Funtronics has the manual for this model.
If there are some parts you are looking for, just post them in the Swap Meet Area section.
|
|
|
|
|
Logged
|
|
|
|
|
collecture
|
|
« Reply #3 on: September 17, 2006, 10:13:19 am » |
|
As with a lot of these vintage machines, you may find that parts from other machines will fit yours as well. Looking at the coin door area - the bottle opener, coin return cup and coin reject slide look the same as what is in my WC44SK. I believe that all the Westinghouse MD series (60MD, 78MD and 102MD) used the same stuff (bottle opener, coin return cup, reject slide, coin box, etc.)
I am 99% sure I have a cap catcher for your machine if you need one. Before you clean up the area inside the coin door though, see if you can get a rough measurement of the dirt line around where the cap catcher went.
|
|
|
|
|
Logged
|
Cav 27, 33, CS-55E-2, 72
S-48 DP
Ideal CC 35, Barq's 55
1930s DP Counter Cooler
Vendo Coin Changers (ea. style - orig w/ stand)
Vendo Junior (rest.), 23 Deluxe, 39D, 44, 56RT, 80SS, 81A (orig), 81D, 6 C.V.
VMC 27, 27A, 81D DP, 110 DP
Westy WC-42-T, WC-44SK, WD-5(2), WB60
Victor C-14
|
|
|
|
Guest
|
|
« Reply #4 on: September 17, 2006, 01:52:30 pm » |
|
I am from Indianapolis, Indiana. as for the Crown puller. i have that. its actuly sitting on my counter top. but the box under it is missing. as for the size i am not quite shure yet. There looks to be a flat peice of metal for the coin mech that is missing that allows the quarter to roll down into the return change spot. As for right now the quarter just spit out the front side of it. I do notice that the cooling unit will have to be rebuilt as the condencer is all rusted up. I was told that it would cool. but after looking at the condition of the condencer i am not quite shure how true the statment is. It shall be a intresting and long lasting tinker project
Jesse
|
|
|
|
|
Logged
|
|
|
|
|
globalcompressors
|
|
« Reply #5 on: September 17, 2006, 05:52:29 pm » |
|
Looks like a great machine to start with.
Welcome to the Board!
Eric
|
|
|
|
|
Logged
|
how's that OBAMA CARE workin' out for ya?
|
|
|
|
sodaworks
|
|
« Reply #6 on: September 17, 2006, 06:57:46 pm » |
|
Welcome aboard Jesse  '>
|
|
|
|
|
Logged
|
TERRY@SODAWORKS RESTORATIONS
Lots of Round Top machines
Buy-Sell-Trade-Restorations
|
|
|
|
johnieG
|
|
« Reply #7 on: September 17, 2006, 09:14:04 pm » |
|
Hello & Welcome! Nice looking machine! the Westinghouse Select-a-Matics are my favorite line of machines of the early 60's era! I currently own a WB60, 78, & 102. model
Yep! looks like you're missing the cap-catcher & the bottle opener and its mounting pocket. if you look at this picture of one of my WB-60's I have one Ebay, you'll see the cap catcher right next to the coinmech, it's long & rectangular, the bottle opener mounts dirrectly behind the opening on the coindoor itself. notot mention the cash/coin-box.
Nice Find! here's a picture of the one on Ebay....
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
collecture
|
|
« Reply #8 on: September 17, 2006, 09:44:42 pm » |
|
Yep, I have a cap catcher that looks like that.
johnieG - What are the measurements of your WB78 cap catcher or are they all the same?
I don't think I have a coin box though - none of mine have an angle like that on the top left.
|
|
|
|
|
Logged
|
Cav 27, 33, CS-55E-2, 72
S-48 DP
Ideal CC 35, Barq's 55
1930s DP Counter Cooler
Vendo Coin Changers (ea. style - orig w/ stand)
Vendo Junior (rest.), 23 Deluxe, 39D, 44, 56RT, 80SS, 81A (orig), 81D, 6 C.V.
VMC 27, 27A, 81D DP, 110 DP
Westy WC-42-T, WC-44SK, WD-5(2), WB60
Victor C-14
|
|
|
|
Guest
|
|
« Reply #9 on: September 18, 2006, 01:48:12 am » |
|
I have the bottel cap opener. thats currently off the door. i dont have the cap ceatcher thought. looks like it was used with out the ceatcher also as it looks like there is dryed up soda on it. As for the coin mech. i cand find any information on the net about it. Maybe its possable you guys can help me out. its a Coin Acceptors, Inc Model no. FP1100-503 SN 3523 which is stamped on the sticker on the side of the coin box. I whent to there web sight but i couldnt find any info on it. Figure its too outdated for them to really care about it. Thanks for any help or direction you can point me into
Jesse
|
|
|
|
|
Logged
|
|
|
|
|
