SMC Discussion Areas
June 16, 2024, 09:18:56 pm *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1] 2  All   Go Down
  Print  
Author Topic: V-63 compressor removal  (Read 8573 times)
0 Members and 1 Guest are viewing this topic.
Guest
« on: December 15, 2005, 01:55:08 pm »

I just got my first machine, a vendo 63.  It's in good shape and runs cold.  The bottom liner is rusted and I'd like to clean it up.  Can I remove the evaporator and the compressor/condensor out as one unit.  I do not want to have to disassemble it and then pay for a recharge of R12.  I am not ready to restore the machine yet, I only want to clean it up at this point.  Please help.  Thanks in advance.

Rob
Logged
90grad
Soda Jerks
*****
Offline Offline

Posts: 1245


Thanks to all our veterans for our freedom!


« Reply #1 on: December 15, 2005, 04:13:54 pm »

Rob,

Welcome to the community!  Yep, you can remove the unit as a whole.  It's best to have the help of another person.  One person can handle the evaporator and the other handle the compressor/condensor.  The compressor assembly is bolted to a plate, which is then bolted to the cabinet.  Just take out the bolts holding the plate to the cabinet and then take out the screws holding the evaporator to the interior tub.  Also, watch the wiring and avoid kinking any lines.  It was designed to come out in one piece.
Logged

Wayne

Mid-Atlantic Chapter

Cavalier 51 (1953)
Cavalier Airline Cooler
7-Up Picnic Cooler
Vendo 110 (1957)
VMC 56 Bottle (1964)
VMC 56 Can
Westinghouse Master Water Bath Cooler
Westinghouse Standard Ice Cooler
Westinghouse WB-102 (1963)
Kevin C
Soda Jerks
*****
Offline Offline

Posts: 971



« Reply #2 on: December 15, 2005, 10:14:56 pm »

Hey BanjoBob

Welcome.

I was in you same boat last October so review my links to my V-56 & my V-63. On pages 4-5 on the V56 thread you will see what I did with a rusted out bottom evaporator shelf.

V-56


V-63

Please check out my V-63 thread & you will how I repaired that machine. I fact I have that V-63 at my office making me money selling sodas.

If you have any questions send me note.

Kevin
Logged

Vendo 63-C   On the job
Vendo 56   Going back together
Vendo 56-C    Waiting for rehab!
Vendo 126  Rough outside but loaded & operational
Vendo 110  Under repair
Ideal 55 -  **For Sale make offer
Glasco 55 -  Waiting
Royal 650  On the job
Lance Snack Machine - On the job
Yarochrehc
Soda Jerks
*****
Offline Offline

Posts: 787



« Reply #3 on: December 15, 2005, 11:09:43 pm »

Hi Rob, and welcome,
The guys are right, usually there is one stud that holds the compressor deck in place, a couple of screws to hold the bracket for the refrigeration lines and wires in place between the upper and lower cabinet, then the four screws holding the evaporator in place.

.............
Bob
Logged

Bob

Restored
Vendo H63B  Coke in use in basement
Original
Vendo V/VF63/7  Pepsi in use

Restoring: Glascock Standard
(2) Vendo 63
(2)Vendo 90
Vendo 126  waiting for paint
VMC 56
Westinghouse WE-6
jasmine64
Soda Jerks
*****
Offline Offline

Posts: 1036



« Reply #4 on: December 16, 2005, 10:21:08 am »

And theres always one hidden screw/bolt that keeps you from getting the thing out .
Either hidden or rusted tight. Have a can of wd-40 on hand.
Logged

Marsha

Cav. CD 22
Choice Vend 168 - Use daily.
jasmine64
Soda Jerks
*****
Offline Offline

Posts: 1036



« Reply #5 on: December 16, 2005, 10:24:00 am »

After removing the thing, it will be a good time to check the drain hole to see if it's clogged and if the hose needs replacing.
Just be careful and not snap it off, or your drain hose will be useless.
Logged

Marsha

Cav. CD 22
Choice Vend 168 - Use daily.
Guest
« Reply #6 on: December 16, 2005, 12:10:17 pm »

I got it all apart last night, pretty easy now that I've done it once.  Sure enough the drain was plugged and the bottom of the upper compartment is pretty rusted.  The screw holes that held the evaporator are totally rusted out and did nothing to hold it down.  What now???  can I just replace this bottom liner, and if so how do I get it out.  Or do I just put a piece of sheet metal over and call it good???  Please help.  Thanks again

Rob




Logged
jasmine64
Soda Jerks
*****
Offline Offline

Posts: 1036



« Reply #7 on: December 16, 2005, 03:05:13 pm »

I think the liner is all one piece, I myself have never replaced it, but someone
did recently and there is a thread on how it was done.
It was removed, another one made and
the insulation was all replaced. Any rust under the insulation was
fixed. I think it's searchable under the general chat.

I have sanded down the rust and used a rust inhibitor on the bottom liner and
then used Rustoleum on it. Joesquid did a 6 month long test on the Rustoleum
Vs krylon silver if you want to compare.

I'll see where it's located.

Here's one.

liner seating

Here's two. I think this is Joe's last post on this.

Krylon vs. rustoleum




Logged

Marsha

Cav. CD 22
Choice Vend 168 - Use daily.
MoonDawg
Soda Jerks
*****
Offline Offline

Posts: 6224



« Reply #8 on: December 16, 2005, 03:38:47 pm »

Follow Jasmines cleaning instructions and the liner will look fine.    Don't be afraid to drill new mounting holes or to  move your evaporator assembly.
Logged

Glen
Pat Pixley
Guest
« Reply #9 on: December 16, 2005, 11:02:18 pm »

Or keep your ear's & eye's open on this site and
 on Ebay for a parts machine.  Vendo 63 are a common machine and there are a few out there that could be a doner
machine. Or if you know some one that does sheet metel work were they can make a new tank  for you that may work also .

  Pat   ':cool:'
Logged
Pages: [1] 2  All   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!