SMC Discussion Areas
March 29, 2024, 08:06:42 am *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Wooden Spacer / Main Door Vendo 56  (Read 5278 times)
0 Members and 1 Guest are viewing this topic.
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« on: July 06, 2017, 12:01:09 am »

My hardware kit is calling for a wooden spacer between the main door and liner???  I don't remember a wooden spacer Huh? Can someone assist?  Is this critical to install the liner without the spacer?  

I did not see the wooden spacer in the service manual.

Thx
« Last Edit: July 06, 2017, 12:06:38 am by Slapshot42 » Logged
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5869


#1 Soda Jerk!


WWW
« Reply #1 on: July 06, 2017, 06:51:09 am »

Tank Liner Spacer
Logged

My six cents,

Jim

Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« Reply #2 on: July 06, 2017, 09:00:31 am »

I noticed that but the description excludes the Vendo 56.  Also
the description on the hardware list says; " Wooden Spacer, main door to liner".
Logged
MoonDawg
Soda Jerks
*****
Offline Offline

Posts: 6224



« Reply #3 on: July 06, 2017, 10:31:18 am »

         There is a wooden spacer that goes around the coin mech. shaft.   It looks identical to the 3 spacers found in 33's.
Logged

Glen
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« Reply #4 on: July 06, 2017, 04:09:44 pm »

        There is a wooden spacer that goes around the coin mech. shaft.   It looks identical to the 3 spacers found in 33's.

Will this work Glen?

http://sodajerkworks.com/onlinepartscatalog/hard-parts/hp121-vendorlator-spacers-detail
Logged
SIGNGUY
Soda Jerks
*****
Offline Offline

Posts: 5442


Collector of Ol Smoothie Rootbeer


WWW
« Reply #5 on: July 06, 2017, 04:20:44 pm »

Funtronics nor soda jerk works sells one specifically for the Vendo 56..but this one pictured might work if the measurements are right.. but I measured it and ended up making one out of a block of wood... it does not have to be round, just the hole has to be large enough for the vend shaft to go through.. I think it was 5/8.
if I recall it's only 1 1/2 inches deep..
Logged

Soda Machine Enthusiast since 1996!
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« Reply #6 on: July 06, 2017, 04:52:11 pm »

Funtronics nor soda jerk works sells one specifically for the Vendo 56..but this one pictured might work if the measurements are right.. but I measured it and ended up making one out of a block of wood... it does not have to be round, just the hole has to be large enough for the vend shaft to go through.. I think it was 5/8.
if I recall it's only 1 1/2 inches deep..


Thanks th one from SJW is as follows; 1.5 L  - od 1-7/16 – id 1/2"
Logged
SIGNGUY
Soda Jerks
*****
Offline Offline

Posts: 5442


Collector of Ol Smoothie Rootbeer


WWW
« Reply #7 on: July 07, 2017, 08:24:11 am »

that one should work then,, the ID hole may have to be bored out a bit, as I think I tried 1/2 as well and was a very tight fit, so went with 5/8

hopefully Jebb will add that to his V56 parts list...
Logged

Soda Machine Enthusiast since 1996!
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« Reply #8 on: July 08, 2017, 08:07:17 pm »

Here is the original one.  The newer one is is pictured left which is sold by SJW for the VMC 33.  The blocks are the same outside diameter but the shaft hole  is smaller on the 33 block and it's slightly less in overall height .
« Last Edit: July 22, 2017, 02:45:57 am by Slapshot42 » Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!