Zink plating, powder coat, or hammertone?

[loman4ec]

I am getting started on my Selectivend 7up machine and one of my Cavalier 55's and I would like to know what everyone likes best for the insides of their machines. I am leaning toward zink since it is the closest to origional. Has anyone had any experience with zink plating? How much did it cost?

[Eric]

Zinc plating ...I'm in Missouri and there's a place near that said they'd run my
stuff through with a order of theirs for $75. So I'm getting shelves ready to go.
My 39 tub I'm going to Powder Coat. It was originally painted or coated with something?
So the door liner and tub will be powder coated. I hear it is VERY tough. BITW powder
coats their liners and tubs.
I'd like to see what it would look like to zinc my 81 tub too. You're rigth it would be closest to
original. I'll get back with you when I get pricing.... Anyone esle have an opion or experience?'>

Eric

[BrianB]

Powdercoating is by far the most durable. But of the three, For something as large a liner, I'd have to say that Powdercoating is also the most expensive. If you go with machine gray, it's one coat and 20 minutes later your done and out the door. If you go with silver, it was recommended to me to also get a clearcoat on top of that which in turn adds to the overall cost. I got my VF117B-H Liner and Bottle Stack/shelves and other knick knacks Powdercoated and it looks awesome. Unfortunately, I don't have a full-up price for it. I ended up getting most of it done for free for fixing the powdercoater's Choicevend machine! But I would estimate that for 14 shelves, 1 liner and the bottle stack it would be well over $300.00.

When it comes to Zinc plating, I haven't found anybody local to do it, so I substitute actual plating by Cold Galvanizing then clearcoating over it. Not quite as indestructible as powdercoating but much more durable and better looking in my opinion than liquid paint when it comes to the internals that were originally zinc'd.

[Eric]

Getting my shelves for my 81 zinc-ed and cleared also the coin box for my 39
and some little parts....
Will photo and give you an update when they're done. This guy said he has had
someone zinc the whole tub/liner to a soda machine.... If these look good and the
price is right I may do the same and powder clear the tub after it's done?
Has anyone done that? zinc-ed the powder coated clear?.....

[sodaworks]

I am sold on hammertone. I get great results with it and you cannot beat the price. It is very durable and if applied right, it looks great. Terry

[Creighton]

Great thread,
Thanks guys, Terry, are you using rattle cans or what? Called around and couldn't find anybody that would zinc plate but it is CA.
Had to show my ID today to buy rattle paint/primer cans for a Jeep suspension part that needs attention. Jees....
Please keep use posted on all findings.
Creighton

[sodaworks]

If I am doing a rather small job I'll use a rattle can, but if I'm doing a tub or shelves anything of volume then I use my paint gun. I bead blast everything that will fit into my blasting cabinet. What doesn't fit I sandblast prior to painting.

[joesquid]

Terry,
  Where do you get hammertone paint for spray-guns?  I've only seen it in cans but would love to use it in my sprayer.  I like it too....very tough finish and a whole lot cheaper than powdercoating!

[Jim]

Eric, here's some information found at their web site:
Hammerite Rust Cap

Call our technical service department (866-774-6371) for the Hammerite Rust Cap retailer closest to you.
If my memory serves me, I used Hammerite Silver Gray

[BryanH]

Joe - there have been several discussions on hammertone over the last month...  Search the forums, there were several good points in each.  I've also found that my Lowes says they can special order it in quarts or gallons (4 per order).  Still waiting for a price.  Also found a site with pretty detailed instructions on how to spray it --> here