Transporting a machine

[obs48167]

HELP 
I'm new to SMC , great site, Looking at my first machine, have done Jukebox and now want to try a soda machine. I have a question, not sure where to look for answer.

What is the best way of moving a machine, standing up or can you lay it flat. I have a ways to transport it.

I have heard that once you lay if flat you need to let it stand for at lest 24 hours so oil can drain back down in to compressor.

[mznb1u]

Welcome to the site!  Warning--this is an addicting hobby!  This is a great group of collectors who will you with just about any SMC problem you can throw at them.

Unless you have a truck where you can transport a machine upright you are left with transporting the machine flat on its back.  I have moved all of my machines by laying them flat in the back of my Dodge Magnum or my wife's mini-van.  Be careful when loading not to put a crease down the back of the cabinet from the door latch.  I usually pad the bumper and latch with several moving blankets.  Then I lay 3 foot sections of 2" PVC pip across the back of the car.  When the machine gets on the PVC it will roll right in.  Makes it very easy to unload as well just remember to remove the PVC during transport or the machine will be moving all over the back of the car!    You might want to pick up a four wheel dolly to put the machine on when you get it to your garage, etc.  They are cheap at Tractor Supply Company or similar stores and they make moving the machine around much easier when you don't have any help around.

You will want to let the machine stand upright for at least 24 hours to make sure that the oil drains back down into the compressor.  I usually wait 48 hours just to be safe.  All of my machines have fired right up with no problems after transport.

Godd luck finding your first machine.  Remember to report back with pictures!

Tim   

[dr galaga]

Welcome to the hobby.  Yep, all of mine have been transported on their back.  Do you know what kind of machine you are going to be looking for?

[RC kid]

Unless you have a large panel truck or a tall enclosed trailer, transporting a machine upright is extremely hazardous to the health and well being of the machine as well as to your auto insurance rates. I too always transport machines by laying them on their back, and waiting at least twenty-four hours after setting up the machine before plugging it in. I haven't had an issue yet.
  I am fortunate though, I have a full size pick-up truck. I have know idea how you guys get by in our hobby without one.

I recommend that you buy a few furniture pads. They are available at most tool stores and they are cheap at $10.00 each, well worth the price when you consider how much they protect the machine from any additional damage that may occur during movement. I bought ten or so and use tham constantly.

[Larry]

If possible, have the machine more towards the passenger side of the vehicle.  I had a bowler slide up and pin me up against the steering wheel once while breaking suddenly.  Lucky for me no crash happened.  I had to pull over and reposition the machine.  Now I use a rope and tie the machine down to where my seats would attatch to the floor of my mini van.  I have to remove both seats for the machines to fit.

Also, as previously stated.  Watch out for that rear door lock.  I have one machine that I bought with that added crease.  I new right away that the guy never padded his before loading.

[Pat Pixley]

I be honest I've done both , but upright in the back of my truck 3 machine
(Vernors ,O.Crush& Hunters )and took them Down to Battlecreek  for pinball at the
zoo and back home again , JohnieG did it also  And I will tell you I wont do that again .

The Rest of the time it's  goes right on their backs,  and I just started using
two 2" wood dows to make it a little easier to roll in the truck  and it work .

myself I like doing the 24 hr rule just to be safe .

[Marvin]

If possible, have the machine more towards the passenger side of the vehicle.  I had a bowler slide up and pin me up against the steering wheel once while breaking suddenly.  Lucky for me no crash happened.  I had to pull over and reposition the machine.  Now I use a rope and tie the machine down to where my seats would attatch to the floor of my mini van.  I have to remove both seats for the machines to fit.

Also, as previously stated.  Watch out for that rear door lock.  I have one machine that I bought with that added crease.  I new right away that the guy never padded his before loading.

I put a crease in the back of my Pepsi 81 when I unloaded it in the back of my Expedition.  I was by myself and realised as soon as I pulled it out what had happened. 

My brother in law went with me to pick up the first machine I ever put in the back of the SUV.  I told him if we had a wreck I could just see the headlines.  "Man Killed by Coke Machine!!"

Marvin

[collecture]

When taking a V-80 machine out of my Tahoe, I went to let the bottom down prematurely and the top caught the roof of the vehicle.
Needless to say I have matching dents 3/4 up on each side of the back! 

[mznb1u]

My brother in law went with me to pick up the first machine I ever put in the back of the SUV.  I told him if we had a wreck I could just see the headlines.  "Man Killed by Coke Machine!!"

Marvin

  I had one of my Stoners slide up on me like that one time.  Luckily, it did not pin me like a pop machine would have but the headline:  "Stoner cause car wreck!" 

[sodaworks]

Welcome aboard. All you have to do is remove your passenger seat and insert machine. LOL