|
johnieG
|
 |
« on: June 01, 2008, 12:23:32 pm » |
|
Well I just finished up this lingering project, it’s a Vernors branded Vendo V132-4/can vendor. Insofar as Can vendors’ goes, it’s not a bad looking machine.
I like this style of can vendor because of the nifty round selection buttons & its clean-cut front looks, plus it's not too difficult to trouble shoot the vending rack.
This machine was a bottle vendor that was converted to 12-oz. cans (by Vendo) by the removal of the vertical bottle rack & the addition of the serpentine style (stamped & formed sheet metal) can rack. something to keep in mind when checking one of these earlier style can machines out, if ANY of the rack positions don’t have at least two cans in each (rack), the machine will not vend ANY of the selections & reject all coins. this can vending machine is a single price, four selection model, but later 24 volt bottle vendors (rectangular selection button style) where able to be converted to four-price / four selection with a conversion wiring harness & a 24 volt/four price coinco unit.
Note that this particular machine takes a 115/120 volt 8-pin single price coinmech, it currently has a Coinco model S75-9400B series, which like the S75-9800B coinco can be set from 5 to $1.55 per vend. But the '9400B series gives change back in dimes & nickels (as opposed to just nickels for the '9800B coinco coinmech)
I ended up repainting the front (red) as it was all scratched up from its years in service, swapped out the compressor deck with a donor unit from a V63 parts machine, & rewired the lower power harness as it was very brittle with age. I also added a heavy duty 14-gauge line cord, & replaced the burnt out ballasts in the light up sign & added a fresh fluorescent lamp. I also printed up some flavor inserts for the selection buttons, & replaced all of the sold out lamps & the “correct change only” lamp.
For those of you interrested in dimentions, here they are; H=64 W=27-1/2” & D=23”. It’s heavier than it looks ( aren’t they all?) it weighs about 400lbs.
|
|
|
|
« Last Edit: June 01, 2008, 12:34:56 pm by johnieG »
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
mznb1u
|
|
« Reply #1 on: June 01, 2008, 12:54:06 pm » |
|
JohnieG, Just like Mr. Belvedere used to say (and the Michigan guys know I'm not talking about the TV Show), you do good work! For the non-Michigan guys see this YouTube video: http://youtube.com/watch?v=5-FcwHKmm4kNice job at giving that machine new life. And you have all my favorite pops from when I was a kid! Although I would sub Orange Crush for Mountain Dew!  Tim |
|
|
|
« Last Edit: June 01, 2008, 12:55:57 pm by mznb1u »
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #2 on: June 01, 2008, 01:07:58 pm » |
|
Thanks! & remember, Parma spelled backwards is AMRAP! ( The Ghoul, late night TV horror show host, who is still alive & kickin' down in Ohio somewere, then again, it is Ohio after all, so is it really living?)
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
Kilroy
|
|
« Reply #3 on: June 01, 2008, 01:12:51 pm » |
|
Nyahahahahahahahaa
- Sir Graves Ghastly
And nice work John!
|
|
|
|
|
Logged
|
"Restored they go for $6-7,000!!"
Member : Michigan Mafia
|
|
|
|
mznb1u
|
|
« Reply #4 on: June 01, 2008, 05:18:22 pm » |
|
"And this beautiful pop machine was used in a movie that I was almost in!"
Bill Kennedy
Sorry I couldn't resist!
|
|
|
|
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #5 on: June 01, 2008, 08:06:24 pm » |
|
Yeah! Good old Bill Kennedy! who else could smoke a cigarette & drink an Irish coffee while Hosting "Sunday at the movies"
Anyway, here's a picture of a Vendo V125-6 bottle vendor rack section for comparison, this is what they (Vendo) swaped out to convert the machine(s) to can vending. ( I just thought it would be interesting to compare the two setups)
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
Pat Pixley
Guest
|
|
« Reply #6 on: June 01, 2008, 11:11:04 pm » |
|
I just saw this machine today and I'm going to tell you guy's it is a good looking machine, it will make someone a nice machine  . pat |
|
|
|
|
Logged
|
|
|
|
|
Yarochrehc
|
|
« Reply #7 on: June 02, 2008, 06:23:15 pm » |
|
Your kidding, Sir Graves is still around!  John thats a great looking machine. Nice job. |
|
|
|
|
Logged
|
Bob
Restored
Vendo H63B Coke in use in basement
Original
Vendo V/VF63/7 Pepsi in use
Restoring: Glascock Standard
(2) Vendo 63
(2)Vendo 90
Vendo 126 waiting for paint
VMC 56
Westinghouse WE-6
|
|
|
|
Kilroy
|
|
« Reply #8 on: June 02, 2008, 06:39:43 pm » |
|
Sir Graves went off the air in the early 80's, and passed away a year or two ago.
Now had he a Vendo square top in the graveyard done in Pepsi boo.....
/duck & run
|
|
|
|
|
Logged
|
"Restored they go for $6-7,000!!"
Member : Michigan Mafia
|
|
|
|
