|
Guest
|
 |
« on: October 01, 2006, 05:50:43 pm » |
|
Machine is good & cold, but developing some condensation problems. Been alitle humid last few days, but not running the A/C. Water is collecting in the bottle storage shelf, not going out the drain tube. Machine is fairly level, but not perfect and drain tube isn't clogged up. Door seals seem fine and feel no cold air leaks or moisture there.
|
|
|
|
|
Logged
|
|
|
|
|
globalcompressors
|
|
« Reply #1 on: October 01, 2006, 07:21:15 pm » |
|
Check door seals. Try a little vaseline. Warm the temperature
of the box up a bit.
On the drain, use new tubing, make a loop,
create a "pea trap" so no air can get up into the box.
Turn the a/c back on!  '>
Eric
|
|
|
|
|
Logged
|
how's that OBAMA CARE workin' out for ya?
|
|
|
|
bubba
|
|
« Reply #2 on: October 02, 2006, 05:42:28 am » |
|
(globalcompressors @ Oct. 01 2006,8:21)
QUOTE On the drain, use new tubing, make a loop, create a "pea trap" so no air can get up into the box. Turn the a/c back on! '> Eric  '> '> |
|
|
|
|
Logged
|
Ken
V-63 -Bottles
2-Cavalier USS-64
VMC ST56B Royal Crown - being built
Vendo HA56C Coke
2-V63C DP
V63C Coke
U-Select-It 5cent candybar machine
|
|
|
|
sodaworks
|
|
« Reply #3 on: October 02, 2006, 10:38:54 am » |
|
Good advise Eric. It's nice to have a Comp. professional onsite..  '>
|
|
|
|
|
Logged
|
TERRY@SODAWORKS RESTORATIONS
Lots of Round Top machines
Buy-Sell-Trade-Restorations
|
|
|
|
Guest
|
|
« Reply #4 on: October 02, 2006, 07:17:43 pm » |
|
Eric does this compressor look like the original, or same model at least, that came in the V-83?
|
|
|
|
|
Logged
|
|
|
|
|
globalcompressors
|
|
« Reply #5 on: October 02, 2006, 09:46:48 pm » |
|
Yes...looks like an orginal to me.
One of the other guys may have had an 83 and could
give a positive ID.
I usually don't see both, unit and machine together. Only when
someone emails a picture, a problem or with one of my units,
installed.
Looks nice! '>
Eric
|
|
|
|
|
Logged
|
how's that OBAMA CARE workin' out for ya?
|
|
|
|
Guest
|
|
« Reply #6 on: November 10, 2006, 01:41:24 pm » |
|
Where is the thermostat control on the compressor pictured above? I still have a problem.
|
|
|
|
|
Logged
|
|
|
|
|
globalcompressors
|
|
« Reply #7 on: November 10, 2006, 02:42:24 pm » |
|
The cold control should be located on the upper evaporator
coil. It will either have a knob with numbers or a slot for a
screwdriver. Turn the unit off, leave it off for 5 min. and turn it back
on. Keep it to where the machine just came on and leave it.
Make sure the machine cycles off. If not...replace the stat.
Eric
|
|
|
|
|
Logged
|
how's that OBAMA CARE workin' out for ya?
|
|
|
|
johnieG
|
|
« Reply #8 on: November 10, 2006, 06:44:42 pm » |
|
As a note, this compressor deck looks like mine on my V83, mine's a Westinghouse compressor & my cold control is located on the side of the big rectangular /relay box, ( note the cap-tube on the upper right side) but my V110 has a standard T-stat located up on the evaporator coil.
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
zadd
|
|
« Reply #9 on: November 10, 2006, 07:46:56 pm » |
|
Stupid question .What is a pea trap?  '>
|
|
|
|
|
Logged
|
Zadd
Dr Pepper Queen Anne Bottle Machine
Dr Pepper Queen Anne Can Machine
7up Ideal 55 slider
Vendo 81D
VMC 33D
Nehi Pelco Koolie
|
|
|
|
