USMC Vet
|
|
« on: November 11, 2005, 07:57:49 pm » |
|
Do I need to turn the cut out screw to make it stay kicked out longer? Cycling too often,will run down to 38 and kick back on at 40,was wanting another 2 degrees.Thanks!
|
|
|
Logged
|
Tony Vendo 81D - Being restored Vendo Dr.Pepper Queen Anne - Very nice original
|
|
|
90grad
|
|
« Reply #1 on: November 12, 2005, 10:38:44 am » |
|
Eric at Global is the authority, but I think you adjust the cut-in screw to keep the compressor off longer.
|
|
|
Logged
|
Wayne
Mid-Atlantic Chapter
Cavalier 51 (1953) Cavalier Airline Cooler 7-Up Picnic Cooler Vendo 110 (1957) VMC 56 Bottle (1964) VMC 56 Can Westinghouse Master Water Bath Cooler Westinghouse Standard Ice Cooler Westinghouse WB-102 (1963)
|
|
|
globalcompressors
|
|
« Reply #2 on: November 13, 2005, 01:52:09 pm » |
|
Kick the "cut in" counter clockwise another 1/4 turn. That should get it close. Remember to have the box full. This will hold temperature for a longer period.
Eric
|
|
|
Logged
|
how's that OBAMA CARE workin' out for ya?
|
|
|
BryanH
|
|
« Reply #3 on: June 10, 2006, 10:38:09 pm » |
|
Where exactly does one find the cut-in screw? There is a tiny screw (looks like a set screw) behind the terminals on the back of the t-stat . Is that it?
|
|
|
Logged
|
Thanks, Bryan Cavalier USS-96: unrestored, working on the back patio CV VUB/C 8-91: a fantasy restoration? GE Cooler: in pieces, my next project
|
|
|
davethebirdman
|
|
« Reply #4 on: June 11, 2006, 01:06:18 am » |
|
Bryan
On the five T Stats I've had there has always been two small screws on the side marked cut in and cut out.
|
|
|
Logged
|
|
|
|
BryanH
|
|
« Reply #5 on: June 15, 2006, 11:11:45 pm » |
|
Hmm - the old tstat had a tiny screw on the back by the connectors with no markings or labels. The one I just bought isn't labelled either. I can only see one screw so I'm assuming that's it.
|
|
|
Logged
|
Thanks, Bryan Cavalier USS-96: unrestored, working on the back patio CV VUB/C 8-91: a fantasy restoration? GE Cooler: in pieces, my next project
|
|
|
davethebirdman
|
|
« Reply #6 on: June 16, 2006, 03:00:52 am » |
|
I'm not sure mate. Are you cutting in or cutting out. Hopefully Eric will step up and let us know.
Can always try and if it doesn't work invest in a new T-Stat.
|
|
|
Logged
|
|
|
|
BryanH
|
|
« Reply #7 on: June 18, 2006, 02:47:06 pm » |
|
Seems to adjust the cut-out (or temp set). I have a note into Steve at the sodajerkworks to see how to set the cut-in.
|
|
|
Logged
|
Thanks, Bryan Cavalier USS-96: unrestored, working on the back patio CV VUB/C 8-91: a fantasy restoration? GE Cooler: in pieces, my next project
|
|
|
globalcompressors
|
|
« Reply #8 on: June 22, 2006, 08:22:51 pm » |
|
I've never seen one with the single screw design. Sorry I won't be of much help. Seems though, if it changes the temp set or cut out, then the temperature diff. will probably be factory set, usually around 4-6 degrees...I would guess??? '>
|
|
|
Logged
|
how's that OBAMA CARE workin' out for ya?
|
|
|
|