SMC Discussion Areas
November 27, 2024, 08:31:39 am *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
SMC Discussion Areas > Trouble-Shooting > Refrigeration (Moderators: johnieG, Jim) > Vendo
Pages: [1]   Go Down
« previous next »
  Print  
Author Topic: Vendo  (Read 5907 times)
0 Members and 1 Guest are viewing this topic.
Guest
« on: January 19, 2006, 10:13:03 am »
i just bought a vendo model number h1263 and it will not cool does anyone have any trouble shooting tips i can try ?the bower is working but no cold air ....i was thinking  the compressor ..since it doesnt click on ...any help would be helpfull
 travis
Logged
Kevin C
Soda Jerks
*****
Offline Offline

Posts: 971
« Reply #1 on: January 19, 2006, 02:38:37 pm »
Hello

Can you post a picture of your machine?

First I would try plugging the compressor directly in with an extension cord. Let it run for a few minutes & then check the upper coil for frosting. If this works then you have an electrical problem if this does not work ( compressor not running) you most likely have refrigeration issues.

Kevin
Logged
Vendo 63-C   On the job
Vendo 56   Going back together
Vendo 56-C    Waiting for rehab!
Vendo 126  Rough outside but loaded & operational
Vendo 110  Under repair
Ideal 55 -  **For Sale make offer
Glasco 55 -  Waiting
Royal 650  On the job
Lance Snack Machine - On the job
Guest
« Reply #2 on: January 19, 2006, 06:18:25 pm »
Hey I tried it and it started cooling so ...that's good news, I was told I need a 3 in 1 starter relay anyone have any ideas?
 Travis
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5396


This is fine...everythings going to be OK....


WWW
« Reply #3 on: January 19, 2006, 06:52:25 pm »
Well, if the compressor started up OK with the extention cord, the good news is that you won't need a 3-in-1 starter/booster! the bad news is that somethings not allowing the compressor to start normally (when it's pluged into its power socket on the wiring harness) I'd start by unpluging the machine, remove the wires from the Thermostat & connect them together temporarily with a jumper wire & electrical tape. then plug the compressor back into the socket down below (on the wiring harness, that is) & plug the machine in...now if the compressor comes to lif, then it's simply a bad thermostat, if not , you'll have to start digging a little deeper into the wiring harness...we'll start here & see where it gets you...here's a basic wiring diagram of what you're working on...hope it helps
Logged
Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
Kevin C
Soda Jerks
*****
Offline Offline

Posts: 971
« Reply #4 on: January 19, 2006, 10:22:57 pm »
Hey

If it worked on the extension cord. Go to Soda Jerk & buy a new wiring harness.  

Kevin
Logged
Vendo 63-C   On the job
Vendo 56   Going back together
Vendo 56-C    Waiting for rehab!
Vendo 126  Rough outside but loaded & operational
Vendo 110  Under repair
Ideal 55 -  **For Sale make offer
Glasco 55 -  Waiting
Royal 650  On the job
Lance Snack Machine - On the job
Guest
« Reply #5 on: January 20, 2006, 04:42:42 am »
ill look into a harness but can you explain to me were the thermostat is '<img'>?seems simple fan works ,compressor works just got to get them to work together ....thanks travis
Logged
Guest
« Reply #6 on: January 20, 2006, 04:48:40 am »
also what harness wil i need ???ill post picks later today of the hole thing thanks travis
Logged
Guest
« Reply #7 on: January 22, 2006, 01:29:31 pm »
ok i jumped the thermostat and the compressor didnt kick on so im going to assume i need a harness .....i hope that will do it
Logged
zadd
Soda Jerks
*****
Offline Offline

Posts: 933
« Reply #8 on: February 11, 2006, 02:19:15 pm »
You might have a vendo h126b '<img'> Usually the wiring harness will do the trick,those machines are pretty much bulletproof. I have two and they work great after cleaning and new fans,wiring harness.
Logged
Zadd
Dr Pepper Queen Anne Bottle Machine
Dr Pepper Queen Anne Can Machine
7up Ideal 55 slider
Vendo 81D
VMC 33D
Nehi Pelco Koolie
Pages: [1]   Go Up
  Print  
« previous next »
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!