|
MoonDawg
|
 |
« Reply #10 on: August 04, 2005, 03:14:23 pm » |
|
Re-read what Mike stated about knobs, that's why the wide bottle door? What do they do?
|
|
|
|
|
Logged
|
Glen
|
|
|
|
loman4ec
|
|
« Reply #11 on: August 04, 2005, 03:46:16 pm » |
|
Glen on a USS-64 the door is wider than a CSS 64. They have a knob for each selection that you rotate and it plops out the selection. It is just a different way for the slant shelf to vend to allow the machine to dispense cans. I would post a pic for you but I am on my Moms computer.
|
|
|
|
|
Logged
|
|
|
|
|
|
|
Guest
|
|
« Reply #13 on: August 04, 2005, 05:21:47 pm » |
|
I cheated... here's the link from the machine section of the site...
USS 8-64 machine
In the picture of the machine open, you'll see a row of knobs to the right of the vending openings. To vend, you rotate those knobs, which causes a can/bottle to vend into the opening. You then can reach in to get to the can. When the machine is closed, when you look through the glass what you see is the row of knobs. Each knob has a sitcker location for the soda label. The side of the door where the cans are retrieved is blocked from view.
It's really a neat machine, very nice size and can vend quite a bit.
|
|
|
|
|
Logged
|
|
|
|
|
Guest
|
|
« Reply #14 on: August 04, 2005, 05:23:21 pm » |
|
Well, my cheat link didn't work as intended... to find the picture, select the link along the left side for Cavalier, then scroll across the top to the USS-64. That's our baby! Sorry about any unintended confusion --
|
|
|
|
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #15 on: August 04, 2005, 05:36:12 pm » |
|
This should help ... this ones on ebay.
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
Guest
|
|
« Reply #16 on: August 05, 2005, 09:46:45 pm » |
|
You know, probably shouldn't say this but... why in the heck would someone post a picture to sell a machine with as nasty of a tub bottom as this machine has? You can just feel the rust in your bones....
|
|
|
|
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #17 on: August 06, 2005, 09:40:57 am » |
|
Actually, also looks like a sticky slick of soda-syrup 
the bottom of the liner/tank of most machines will usually have some surface rust, but letting a puddle sit on the bottom, (caused by a plugged drain) will rust out the metal quickly, especially around the screws that hold the evaporator housing to the tank bottom, and from there it'll turn into a "wet blanket" of insulation underneath the liners floorpan & rot the machine from the inside out....  '>
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
loman4ec
|
|
« Reply #18 on: August 06, 2005, 10:38:25 am » |
|
Bminer, Please contact me asap if you want parts. I am moving Monday early morning and I do not plan on taking these with me so if you want them please contact me prior tp monday or I am going to leave them at my mothers house. I also found you a coin box.
|
|
|
|
|
Logged
|
|
|
|
|
sodaworks
|
|
« Reply #19 on: August 06, 2005, 11:09:19 pm » |
|
I checked and i do not have a bezel.
|
|
|
|
|
Logged
|
TERRY@SODAWORKS RESTORATIONS
Lots of Round Top machines
Buy-Sell-Trade-Restorations
|
|
|
|
