SMC Discussion Areas
November 10, 2024, 02:48:49 pm
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News
:
Home
Help
Login
Register
SMC Discussion Areas
>
Restorations
>
General
(Moderators:
johnieG
,
Jim
) >
Cleaning the inside
Pages: [
1
]
Go Down
« previous
next »
Print
Author
Topic: Cleaning the inside (Read 6760 times)
0 Members and 1 Guest are viewing this topic.
Guest
Cleaning the inside
«
on:
April 15, 2004, 10:22:35 am »
What do you recommend to clean the galvanized surfaces of the inside of the machine? Mine is somwhat chalky, as well as just dirty. Steel wool? Soap and water? Thanks - Ace
Logged
Guest
Cleaning the inside
«
Reply #1 on:
June 13, 2004, 05:04:40 pm »
Hope someone replies, I'm interested to know myself.
Logged
Coke Machine Novice
Guest
Cleaning the inside
«
Reply #2 on:
June 13, 2004, 06:54:52 pm »
I saw cleaning tips on the 4th page of this discussion forum. They said to use TSP which is used by painters.
Logged
BrianB
Soda Jerks
Offline
Posts: 2215
Cleaning the inside
«
Reply #3 on:
July 11, 2004, 12:07:34 pm »
I just got done cleaning out my VMC117 after it had been sitting idle in a barn hosting a family of mice for a bunch of years. I used Simple Green to cut all of the dirt on all surfaces. I'd estimate that the dirt and grime inside was about 1/8" to 1/4" thick. I would also have to say with some confidence that it had never been cleaned during it's service life.
For all of the galvanized surfaces I used C.L.R. I used a 30 gallon trash can filled with hot water using a 1 to 8 ratio of C.L.R. to water. The bottle recommends that you only let it soak for 2 mins or possible damage may occur. Well....I ended up checking it after 2 mins and it was working quite well but I figured I'd leave it in for a bit longer. "A Bit Longer" turned into about 2 hours! The particular peice that I was soaking was the Compressor Fan shroud. It was pretty nasty when it began it's soak. I used a stiff bristle brush to agitate the build up and it came right off! I had another garbage can with clean water for the rinse. After all was said and done the shroud looked good as new! For all other "static" or parts that have stay where they are i.e the inside of refrigerated portion. I used a spray bottle filled with C.L.R. and a sponge using the "greenie weenie" side and used another sponge with fresh water to rinse. So, in conclusion, C.L.R. worked great for all galvanized surfaces while Simple Green did a bang up job everywhere else.
Logged
Brian
Jim
Administrator
Soda Jerks
Offline
Posts: 5880
#1 Soda Jerk!
Cleaning the inside
«
Reply #4 on:
July 11, 2004, 06:08:25 pm »
Thanks for the tip on C.L.R.!
Logged
My six cents,
Jim
Bob K
Soda Jerks
Offline
Posts: 803
Cleaning the inside
«
Reply #5 on:
July 12, 2004, 07:38:49 am »
Well, don't I feel like the weenie, but what exactly is CLR?
'>
Bob
Logged
dr galaga
Soda Jerks
Offline
Posts: 2346
Sorry, but it's a POP MACHINE!
Cleaning the inside
«
Reply #6 on:
July 12, 2004, 08:20:05 pm »
CLR (Calcium, Lime and Rust Remover) is a cleaner that you can find at the grocery or drug store. Here's a link with a picture:
http://www.polsteins.com/clrcallimrus.html
There, now you shouldn't feel like a weenie
!
Logged
Brent
--------------
Cavalier CS-80C
Vendo 63
--------------
The ultimate glass bottle soda site:
www.GlassBottleSoda.org
My gameroom:
Arcade80s.net
Bob K
Soda Jerks
Offline
Posts: 803
Cleaning the inside
«
Reply #7 on:
July 13, 2004, 07:23:30 am »
Thanks Doc! I don't feel so "weenie-like" now!
'>
Logged
Pages: [
1
]
Go Up
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
The Coin Return
-----------------------------
=> Soda-Machines.Com News
=> Other Coin-Op's
=> General Chit Chat
=> Estimated Values
=> Tutorials & Tips
-----------------------------
Soda Machines, Coolers & Dispensers
-----------------------------
=> Pre 60's Machines & Coolers
=> Post 60's Machines & Coolers
=> Picnic Coolers
=> Syrup Dispensers
-----------------------------
Trouble-Shooting
-----------------------------
=> Coin Mechanisms
=> Refrigeration
=> Vending Mechanisms
-----------------------------
Restorations
-----------------------------
=> General
=> Refinishing
-----------------------------
The Vending Rack
-----------------------------
=> Swap Meet Area
Loading...