SMC Discussion Areas
March 28, 2024, 08:48:27 am *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Need help with a Vendo 39 latch  (Read 6328 times)
0 Members and 1 Guest are viewing this topic.
vendo39
10 Cent Member
***
Offline Offline

Posts: 243



« on: October 15, 2008, 10:33:41 am »

I’m just about finished with my first ever Coke machine restoration  biggrin(it’s a Vendo 39) but I seem to be having trouble getting the latch on the main door to work properly.  The latch will grab the striker ok but when I push the handle all the way up to lock the door tight, the handle wants to pop back down.  I’ve added washers and I‘ve taken washers out. I’ve moved the striker up and I’ve moved the striker down.  None of this seems to make any difference. It won’t stay tight. darn

Any ideas on what the typical adjustment is to make the latch hold tight?

Could the handle actually just be worn out?

Thanks
Logged

Brian

Vendo 39, 44, 56, 81B
Vendo Changer, early
Vendo Changer, late
Dr. Pepper Queen Anne
Nesbitts Ideal 85

Popperette, Stoner JR, Stoner 180,
Stoner Theater, Mills Candy, Canteen Candy
MoonDawg
Soda Jerks
*****
Offline Offline

Posts: 6224



« Reply #1 on: October 15, 2008, 10:45:50 am »

       Yes, the handle is worn. It should be slightly rectangular where the latch meets
the body, but yours has been worn "rounded" at that critical point.
Logged

Glen
coke_and_stuff
Soda Jerks
*****
Offline Offline

Posts: 3253



« Reply #2 on: October 15, 2008, 12:17:46 pm »

If you need one I have several here.

coke_and_stuff@yahoo.com

Joey
Logged

Collector of nice original paint machines

Vendo 81 B, C, D
VMC 81 Pepsi, 7up, RC, Generic
6CV Coke, RC, Pepsi
VMC 110 RC
Vendo 39
Jacobs 26
Mills 47
Selectivend 64 7up NOS
Plus 30-50 parts and project machines
vendo39
10 Cent Member
***
Offline Offline

Posts: 243



« Reply #3 on: October 15, 2008, 01:53:57 pm »

Joey,

I guess I do need a different one.  I was thinking of trying to build up the hinge up with my welder but if you have a replacement I'll go that route.  I'll  send an email to your Yahoo account.
Logged

Brian

Vendo 39, 44, 56, 81B
Vendo Changer, early
Vendo Changer, late
Dr. Pepper Queen Anne
Nesbitts Ideal 85

Popperette, Stoner JR, Stoner 180,
Stoner Theater, Mills Candy, Canteen Candy
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« Reply #4 on: July 22, 2017, 02:39:46 am »

I have having a similar issue .  I can't get the door handle to latch on the striker.  I have adjusted it half a dozen time.   darn
Logged
MoonDawg
Soda Jerks
*****
Offline Offline

Posts: 6224



« Reply #5 on: July 22, 2017, 10:47:00 am »

  I can't get the door handle to latch on the striker. 

      Not sure if your problem is the same, but as a solution to the original question in this post, as stated the pivot point on the latch has become rounded out.
Remove it, open it fully and grind one edge of the latch until the corner becomes square again, re-install and shim if needed.
Logged

Glen
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« Reply #6 on: July 22, 2017, 05:17:57 pm »

      Not sure if your problem is the same, but as a solution to the original question in this post, as stated the pivot point on the latch has become rounded out.
Remove it, open it fully and grind one edge of the latch until the corner becomes square again, re-install and shim if needed.


2 washers behind the striker latch seems to work!!  biggrin
Logged
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5868


#1 Soda Jerk!


WWW
« Reply #7 on: July 22, 2017, 08:55:08 pm »

There's supposed to be two spacers behind the flange on the liner; one for each 1/4-28 that fastens the receiver. If these are not installed, there is the possibility of setting the receiver too far back, the spacers prevent this, thus a possible issue with correct door latch function...
Logged

My six cents,

Jim

Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« Reply #8 on: July 23, 2017, 01:31:01 am »

There's supposed to be two spacers behind the flange on the liner; one for each 1/4-28 that fastens the receiver. If these are not installed, there is the possibility of setting the receiver too far back, the spacers prevent this, thus a possible issue with correct door latch function...

Thankfully, the 2 washers worked ...
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!