SMC Discussion Areas
March 29, 2024, 07:43:55 am *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: 1 [2]  All   Go Down
  Print  
Author Topic: Need Service Manual for S75-9400  (Read 15432 times)
0 Members and 1 Guest are viewing this topic.
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5869


#1 Soda Jerk!


WWW
« Reply #10 on: November 28, 2007, 05:12:47 pm »

Jasmine64 has this available if you need the light harness...

a sign wiring harness from a Vendo 63 door
Logged

My six cents,

Jim

ronko
Guest
« Reply #11 on: November 29, 2007, 10:54:07 am »

           
                Thanks again JohnnyG , I checked the wires but the numbers (if they were numbers) were too faded. I'll use a homemade continuity light to identify where each wire ends, then use your diagram to place the wires on the female Jones plug.
               
                                                    Ronko
Logged
ronko
Guest
« Reply #12 on: November 29, 2007, 10:59:44 am »


                     Thanks Jim for the info, but it appears the light harness is intact. Just need to re-plug it back and should work .

                                                                Ronko
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5387


This is fine...everythings going to be OK....


WWW
« Reply #13 on: November 29, 2007, 02:05:08 pm »

Here's the actual wiring diagram for a Vendo V90, same as the V63, minus the bottle gate light portion 0f the circut. as most V63's didin't have a flourecent lamp for the bottle door, some did have  a small C7 type light at the very top of the bottle door portal.

but other than that , it's identical...
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
ronko
Guest
« Reply #14 on: November 30, 2007, 11:00:31 am »



            Great ! Thanks for the V63 diagram JohnieG . I'll try to assemble the wires this weekend and see what happens.

                                                                 Ronko
Logged
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« Reply #15 on: August 20, 2016, 07:04:17 pm »

No problem, at first glance a S75-9400 looks like a S75-9800 A model, but then you'd notice that it has an extra change/inventory switch marked 10-Cents, that's because if you look closer, you'd see that one of it's cange-tubes actually holds dimes! other rhan that, it functions almost identically to the S75-9800/A model, it can be set from 5 to 75 cents per vend ( it's a single price coinmech) & it gives change back in nickels or dimes, & plugs into any machine that takes a standard 120-volt AC / 8-pin "jones" plug ( you don't count the middle "round" index/polarity pin, just the rectagular blades/prongs)

Bringing this thread back from the dead!

I don't see the little dip switches for setting the price?  Anyone have an idea?

Thanks!!
« Last Edit: August 20, 2016, 07:09:54 pm by Slapshot42 » Logged
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5869


#1 Soda Jerk!


WWW
« Reply #16 on: August 20, 2016, 07:12:46 pm »

Possibly a "fixed" price unit...
Logged

My six cents,

Jim

MoonDawg
Soda Jerks
*****
Offline Offline

Posts: 6224



« Reply #17 on: August 20, 2016, 07:22:08 pm »

       Take the back cover off to find dip switches on the older models.
Logged

Glen
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2627


Jared


« Reply #18 on: August 20, 2016, 07:24:56 pm »

       Take the back cover off to find dip switches on the older models.

Thanks, I will investigate it.
Logged
Pages: 1 [2]  All   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!