SMC Discussion Areas
June 15, 2024, 02:55:42 pm *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Cavalier cs-80c restoration begins  (Read 2780 times)
0 Members and 1 Guest are viewing this topic.
dr galaga
Soda Jerks
*****
Offline Offline

Posts: 2346


Sorry, but it's a POP MACHINE!


WWW
« on: July 11, 2006, 04:00:38 pm »

Well, I took the plunge.  Eric has my cooling system and I dropped the shell and some parts off at a local body shop.  
A few questions:  
1) The door liner has some chunks missing by almost all of the screws holes.  I was thinking about just using some black plastic washers since the door gasket hides the screw heads.  Anyone else do something different in the past?
2) During an earlier paint job someone painted part of the polished stainless steel bottle door opening white.  Do you think paint remover and a sponge will remove this okay?
3) Does anyone make the bottle door gasket?  I found some gaskets at Funtronics that will work for the main door, but they don't seem to have any bottle door gaskets like this in their catalog.
4) Is anyone making (or does anyone here have an extra) small gold piece that goes below the silver kick plate in the front or a Calavlier logo that goes on the bottom of the front of the machine?

First pic the liner and second pic the piece that goes in the bottle door opening.
Logged

Brent
--------------
Cavalier CS-80C
Vendo 63
--------------
The ultimate glass bottle soda site: www.GlassBottleSoda.org
My gameroom: Arcade80s.net
dr galaga
Soda Jerks
*****
Offline Offline

Posts: 2346


Sorry, but it's a POP MACHINE!


WWW
« Reply #1 on: July 11, 2006, 04:05:14 pm »

Here's the empty machine.  Since we have carpet on the stairs, I just set the machine on it's side and pushed it up the basement stairs.  Sure was a lot easier than when I took it down originally!  ':p'

Maybe if this project goes well, I'll finally restore my first machine that I got as a freshman in high school.  '<img'>
Logged

Brent
--------------
Cavalier CS-80C
Vendo 63
--------------
The ultimate glass bottle soda site: www.GlassBottleSoda.org
My gameroom: Arcade80s.net
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5873


#1 Soda Jerk!


WWW
« Reply #2 on: July 11, 2006, 09:19:44 pm »

Hey Brent,

Quote
A few questions:  
1) The door liner has some chunks missing by almost all of the screws holes.  I was thinking about just using some black plastic washers since the door gasket hides the screw heads.  Anyone else do something different in the past?

If you can't find a nice original for a replacement liner(yea, right...), I recommend visiting your local sheet metal shop and acquire thin galvinized strips of metal approx. 3/8" - 1/2" wide to hold the liner in place. Use a punch to make holes that line up with the cabinet door holes and just screw this in place as you would while re-attaching the liner and door gasket. The galv. strips will act as a long trim washer and reinforce the plastic door liner as well so future breakage shouldn't occur.
Quote

2) During an earlier paint job someone painted part of the polished stainless steel bottle door opening white.  Do you think paint remover and a sponge will remove this okay?

Paint stripper works fine on stainless steel
Quote

3) Does anyone make the bottle door gasket?  I found some gaskets at Funtronics that will work for the main door, but they don't seem to have any bottle door gaskets like this in their catalog.

Perhaps one of the suppliers can give you a little more insight as to what may be a good substitute...
Quote

4) Is anyone making (or does anyone here have an extra) small gold piece that goes below the silver kick plate in the front or a Calavlier logo that goes on the bottom of the front of the machine?

No help on this one...
Logged

My six cents,

Jim

Lulu
Guest
« Reply #3 on: July 12, 2006, 08:38:20 am »

For the door liner, I  used some black plastic strips I found at Menard's in the suspended ceiling section.  I think it was Brian that recommended this in a earlier post.
Logged
dr galaga
Soda Jerks
*****
Offline Offline

Posts: 2346


Sorry, but it's a POP MACHINE!


WWW
« Reply #4 on: July 13, 2006, 11:27:53 pm »

Thanks for the advice.  I'll let you all know what I find/decide on!
Logged

Brent
--------------
Cavalier CS-80C
Vendo 63
--------------
The ultimate glass bottle soda site: www.GlassBottleSoda.org
My gameroom: Arcade80s.net
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!