Need parts help

Guest

« on: October 09, 2005, 02:10:13 am »

Can someone help me locate light up signs for my Pepsi VMC-56? I also need a can rack and compressor setup for a Vendo-63. And why are all the good soda machines in the mid-west? I'm feeling neglected in California!!!! '<img

'>

Maverick


	Logged

Kevin C

Soda Jerks

Offline

Posts: 971

Need parts help

« Reply #1 on: October 09, 2005, 08:56:36 am »

Hello & Welcome

The first thought from everyone here is can you post some pictures of your toys?

I have a Pepsi sign out of a VMC 56 that I could part with but I will only sell the plastic insert. I need the frame for my coke V56 that I am converting to a light up model.

Send me a note if you want it.

Kevin


	Logged

Vendo 63-C On the job
Vendo 56 Going back together
Vendo 56-C Waiting for rehab!
Vendo 126 Rough outside but loaded & operational
Vendo 110 Under repair
Ideal 55 - **For Sale make offer
Glasco 55 - Waiting
Royal 650 On the job
Lance Snack Machine - On the job

Guest

Need parts help

« Reply #2 on: October 09, 2005, 04:32:34 pm »

Thanks Kevin!!! I also forgot to ask if anyone knows where to get the small bulb type weatherstripping that goes around the frame for the light-up signs?


	Logged

sodaworks

Soda Jerks

Offline

Posts: 3532

Need parts help

« Reply #3 on: October 10, 2005, 11:19:10 pm »

Hello Maverick,
Welcome aboard, but there's still lots of good finds here in California. I post one tomorrow from my road trip today!!! '<img


	Logged

TERRY@SODAWORKS RESTORATIONS
Lots of Round Top machines
Buy-Sell-Trade-Restorations

Eric

Soda Jerks

Offline

Posts: 4860

Need parts help

« Reply #4 on: October 10, 2005, 11:50:49 pm »

Maverick...
I'm in Missouri and there ain't anything! I think I bought the last known round top this past May
cause I ain't seen nothing since... Though Josh is running up and down the Midwest buying everything....

It's all in California in two places.... Terry's shop or Glen's shop... They're magnets.... They probably
just sit on the beach out there with a magnet and the machines just draw to them...... '<img

'>

Welcome to the board..... Somebody will have what you need...

Eric


	Logged

Eric

WANTED:
Embossed Quikold Standard

Guest

Need parts help

« Reply #5 on: October 11, 2005, 09:27:01 am »

I tried to post this last night but it didn't work, so I'm gonna try again.
Hey thanks for the warm Welcomes everyone!!!
Did anyone see the VMC 27 on eBay that they want $495.00 for shipping? '<img

'> Aren't these machines under 100lbs. Huh?

Does anyone near me have a BIG (6ft and over) square corner light-up Pepsi machine that they want to sell??

Maverick


	Logged

MoonDawg

Soda Jerks

Offline

Posts: 6227

Need parts help

« Reply #6 on: October 11, 2005, 12:04:24 pm »

MoonDawg has a couple of VMC 27's for sale too. And a square light up Pepsi................ in Calif


	Logged

Glen

Eric

Soda Jerks

Offline

Posts: 4860

Need parts help

« Reply #7 on: October 11, 2005, 04:07:24 pm »

See... told you...aaalllllllllll in California!.... '<img

'>

Eric


	Logged

Eric

WANTED:
Embossed Quikold Standard

Guest

Need parts help

« Reply #8 on: October 11, 2005, 05:07:20 pm »

OK......I guess I should get a little more specific. I would like a 60's, early 70's machine.

I guess I'm just not as good at finding machines as everyone else is!!!!!! '<img


	Logged

coke_and_stuff

Soda Jerks

Offline

Posts: 3253

Need parts help

« Reply #9 on: October 11, 2005, 07:23:45 pm »

Eric not all in CA but still some left in North central AR, I just located a old westinghouse upright, and a few old square tops.

Joey


	Logged

Collector of nice original paint machines

Vendo 81 B, C, D
VMC 81 Pepsi, 7up, RC, Generic
6CV Coke, RC, Pepsi
VMC 110 RC
Vendo 39
Jacobs 26
Mills 47
Selectivend 64 7up NOS
Plus 30-50 parts and project machines

Pages: [1] 2 All Go Up

« previous next »

	Author	Topic: Need parts help (Read 6751 times)
0 Members and 1 Guest are viewing this topic.