SMC Discussion Areas
December 10, 2024, 06:21:47 am *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: VMC44 thermostat - A12-700 or 701 ?  (Read 4984 times)
0 Members and 1 Guest are viewing this topic.
canton335
Newbie
*
Offline Offline

Posts: 8


« on: September 08, 2020, 07:27:18 pm »

I'm trying to figure out if I have the correct thermostat in my VMC44.  I'm just getting back to putting the machine into service and I'm not sure about the temps it's running. 

Air temp about half way up the empty bottle rack is ranging from 26F to 38F with the thermostat on #3.  I'm running the A12-700, but was wondering if maybe I shouldn't have went with the 701.

I'm not sure what's "normal" for an empty machine.

Any help appreciated.

Logged
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5881


#1 Soda Jerk!


WWW
« Reply #1 on: September 10, 2020, 06:02:25 am »

Keeping the machine at least 3/4 full of product would yield accurate results. I am uncertain as to the functionality of the thermostat models you listed...
Ensure the fan blade is correct for evaporator motor rotation also.
Logged

My six cents,

Jim

canton335
Newbie
*
Offline Offline

Posts: 8


« Reply #2 on: September 10, 2020, 05:02:10 pm »

I'm flying a little blind here.  I put the machine back together the way I received it.  Which way should the air be moving over the evaporator ?

I should be able to fill it up this weekend and get some better readings.

As for the thermostats, from what I can tell, the 700 regulates from 37F to 26F and the 701 is from 41F to 31F at their warmest settings.
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5397


This is fine...everythings going to be OK....


WWW
« Reply #3 on: September 11, 2020, 06:52:16 pm »

I use the RANCO A30-2210 on almost all of my repairs, it's an air-sensing type that has a Range of 30F to 43F with a differential of 8 deg. F

Plus it comes with an attractive face-plate & control knob.
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
canton335
Newbie
*
Offline Offline

Posts: 8


« Reply #4 on: September 15, 2020, 08:53:51 am »

Thank you for the information on the Ranco.  I will definitely check it out.
Logged
canton335
Newbie
*
Offline Offline

Posts: 8


« Reply #5 on: September 15, 2020, 05:18:56 pm »

Hey. So I never did get an answer.   Which way is the air supposed to move over the evaporator?
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5397


This is fine...everythings going to be OK....


WWW
« Reply #6 on: September 15, 2020, 06:12:51 pm »

typically in the front & out of the back / up the rear wall,  but on a V44 I believe it pulls air in from the bottom and blows up into the bottle stack
« Last Edit: September 15, 2020, 06:16:18 pm by johnieG » Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
canton335
Newbie
*
Offline Offline

Posts: 8


« Reply #7 on: September 15, 2020, 07:30:24 pm »

Thank you very much for the information.  I believe this machine was in original condition when I got it and you have confirmed the air flow for me.  That's the way it was flowing when I received it and the way it is flowing now. 

Thanks again.
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!