SMC Discussion Areas
November 23, 2024, 07:51:55 am *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: 1 2 [3]  All   Go Down
  Print  
Author Topic: Vernors Quikold 1400CWD  (Read 12494 times)
0 Members and 3 Guests are viewing this topic.
FlaJunkie
Newbie
*
Offline Offline

Posts: 46



« Reply #20 on: September 18, 2020, 08:01:31 am »

...so the machine will receive an entire new cooling deck as well...
Did you use one from a refrigerator? Has anyone ever done that?
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5396


This is fine...everythings going to be OK....


WWW
« Reply #21 on: September 18, 2020, 08:43:29 am »

Huh? No, the compressor deck shown in the prior pictures is a new unit.

I don’t install used compressors.  I know some other people have installed old refrigerator units to replace bad compressors because I’ve repaired a few machines it’s been done to. I don’t recommend it unless it’s an identical model from an identical machine.  Otherwise you’re mixing bad apples with a lemon.  tounge
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
FlaJunkie
Newbie
*
Offline Offline

Posts: 46



« Reply #22 on: September 18, 2020, 10:28:50 am »

Huh? No, the compressor deck shown in the prior pictures is a new unit.

I don’t install used compressors.  I know some other people have installed old refrigerator units to replace bad compressors because I’ve repaired a few machines it’s been done to. I don’t recommend it unless it’s an identical model from an identical machine.  Otherwise, you’re mixing bad apples with a lemon.  tounge
Cool. The replacement compressor assemblies don't look too expensive.
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5396


This is fine...everythings going to be OK....


WWW
« Reply #23 on: September 23, 2020, 07:41:48 pm »

Here's the new Evaporator mocked up & ready for the lines to be brazed to the compressor deck down below, the blue color is just a protective plastic film that peels off after you are done mounting the unit.

The straps you see are just some cargo straps I'm using to clamp the lid-rail in place while I drilled some pilot holes for the new mounting screws, ( which worked out very well)
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
cohammer
Soda Jerks
*****
Offline Offline

Posts: 961



« Reply #24 on: September 24, 2020, 07:10:46 pm »

That’s a lot of good looking copper tube work
Logged

Ideal 35 RC
v 23 deluxe
v 39
c 96
c 55 e
C 51 g
C 72
C96
V 27
Westinghouse JR ice chest
Westinghouse standard ice chest
Westinghouse master ice chest
early model Stoner jr.
Stoner theaters
Thanks Jeff
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5396


This is fine...everythings going to be OK....


WWW
« Reply #25 on: October 04, 2020, 08:03:06 pm »

Well finally wrapped up the Vernors Quikold 1400WD

it's cooling like a champ & quiet as a kitten purring...  I've decided that the new evaporator style will be used in my future rebuilds, they have a smaller version that will make a nice conversion for an Ideal-55 or a Glasco-50.

I ended up moving the T-stat topside for easy access, plus I wont have to worry about the hot compressor area in the summer effecting the control range if it were mounted down below. the biggest pain was tweaking the bottom lid back to some resemblance of squareness so it wouldn't bind in the tracks, the core of these lids is plywood, so they can warp quite a bit. now they slide easy & seal well, I had to add some plastic glide strips along the side-edges to reduce the metal on metal friction, worked like a charm.

« Last Edit: October 04, 2020, 08:09:57 pm by johnieG » Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5396


This is fine...everythings going to be OK....


WWW
« Reply #26 on: October 04, 2020, 08:12:00 pm »

Pic of the compressor compartment, the plastic tray to the far left is a substitute for the missing original cap-catcher , not show is the drip tray.
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
Eric
Soda Jerks
*****
Offline Offline

Posts: 4860



« Reply #27 on: October 05, 2020, 01:04:57 pm »

Great work... it's ready to go another 60+ years!
Logged

Eric

WANTED:
Embossed Quikold Standard
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5396


This is fine...everythings going to be OK....


WWW
« Reply #28 on: October 08, 2020, 08:44:15 pm »

Thanks Eric, it’s been a fun project, BTW for those of you who pm’d me regarding the compressor unit, it’s a Copland R134a 1/5 Hp 950/btw model in conjunction with 99” of SUPCO#2. Capillary line , that along with the higher efficiency evaporator assembly, it’s running 33 degrees F at the #4 setting on the T-stat,    also I replaced the old cork thermal tape under the top trim pieces with a thin closed cell foam tape to keep the heat transfer from sweating up around the upper trim.  & between the tank liner & the lid support stainless steel channel.
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
cohammer
Soda Jerks
*****
Offline Offline

Posts: 961



« Reply #29 on: October 09, 2020, 09:28:51 pm »

That’s a great cooler , not many around for sure .
Logged

Ideal 35 RC
v 23 deluxe
v 39
c 96
c 55 e
C 51 g
C 72
C96
V 27
Westinghouse JR ice chest
Westinghouse standard ice chest
Westinghouse master ice chest
early model Stoner jr.
Stoner theaters
Thanks Jeff
Pages: 1 2 [3]  All   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!