SMC Discussion Areas
December 15, 2019, 10:11:40 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: 1 [2] 3  All   Go Down
  Print  
Author Topic: Wiring Diagram Cavalier 27  (Read 829 times)
0 Members and 1 Guest are viewing this topic.
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2580


Jared


« Reply #10 on: November 27, 2019, 09:47:17 PM »

Nope, just the two-lead model, the replacement compressor harness has an accessory connector that supplies line voltage ( not switched) it’s just not show in my state of the art drawing...   tounge  I just tapped onto that & wired it into the upper terminal strip to supply line voltage to the vending & sold-out circuit.

Yep that’s the pileup I remember!    Oo    Jeeze, they always look so cute & innocent on the surface, ( just like kids  laugh  ).  

Since mine is removed can I use a 3 lead like a 81 door light to power the terminal board ? I have bought both suppliers wiring harnesses . SJW ( EP15 ) one comes with (2) leads t stat and , evap fan.  Usually have to open the trap door in the back at add a 16 gauge wire with ring terminals for hot wire.  FunTronics wiring harness comes with about 3” of wire with a weird round plug.  I usually cut that off and add spade terminals for a hot wire.

Thanks for the help!!
« Last Edit: November 27, 2019, 09:55:16 PM by Slapshot42 » Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5147


This is fine...everythings going to be OK....


WWW
« Reply #11 on: November 28, 2019, 11:31:48 AM »

Either type of power harness will work, I just prefer the Dixie-Narco molded rubber style, btw the weird little round connector is called a “Lyall” plug ( pronounced “lie-all”) they come in two and three pin models, they are quite common on large commercial coolers, where many fan motors come pre-wired with it ( the Lyall plug) as a disconnect means to make servicing to change  them out easier where you’d have many of them say in a grocery store, etc.

And now you know more than you’d ever want to know about Lyall plugs.  tounge
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220, 221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
Because 11 is louder than 10...
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2580


Jared


« Reply #12 on: November 28, 2019, 12:01:23 PM »

Is the Dixie Narco style from SJW or do you have a different supplier ?  Thx
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5147


This is fine...everythings going to be OK....


WWW
« Reply #13 on: November 28, 2019, 12:57:40 PM »

I buy mine locally, but yes, it’s the same.
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220, 221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
Because 11 is louder than 10...
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2580


Jared


« Reply #14 on: November 30, 2019, 08:53:39 PM »

After cleaning the original junction box the HP rating is 1/8 hp.  Also looking for a replacement fan blade as mine is broken.  I measured it at at 6” wide .  It resembles the fan below the pre-cool shelf of the VMC 33 . 
« Last Edit: November 30, 2019, 09:01:18 PM by Slapshot42 » Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5147


This is fine...everythings going to be OK....


WWW
« Reply #15 on: November 30, 2019, 09:28:26 PM »

Hmmm mine said 1/5,  but the 3-in-1 mentioned earlier in the thread has a range from 1/12 to 1/5HP so you should be good, that’s a very early version of a tri-blade fan. They are prone to cracking were the blades meet the deep-drawn hub.
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220, 221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
Because 11 is louder than 10...
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2580


Jared


« Reply #16 on: November 30, 2019, 09:37:38 PM »

Agreed the serial tag was worn with no number .  Thought it was worth putting the actual HP rating down for reference.

Now to find a fan blade ...
« Last Edit: November 30, 2019, 09:39:10 PM by Slapshot42 » Logged
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2580


Jared


« Reply #17 on: December 01, 2019, 11:40:45 PM »

New 3 - 1 - how did you get ring terminals to fit in the threads of those terminals ?  There is small channel for the wire to go through my ring terminal shoulder / collar is to long to find inside there .  I tried bare wire with a loop and it starts up just not sure good of connection I’m getting .  I’ve seen some people tin solder the wire . 
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5147


This is fine...everythings going to be OK....


WWW
« Reply #18 on: December 02, 2019, 11:54:01 AM »

Don’t know about your compressor model, but mine had phenolic plastic binding post terminals , I just removed the phenolic caps & replaced them with 10-24 nuts & some washers.
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220, 221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
Because 11 is louder than 10...
Slapshot42
Soda Jerks
*****
Offline Offline

Posts: 2580


Jared


« Reply #19 on: December 02, 2019, 01:24:19 PM »

Mine are the same with the caps.  Regardless of how your fastening how are you getting the ring terminal to fit on those posts?  I assume your fastener is sort of bending and seating itself as it’s fastened down ?

A few fan blade options -

https://www.grainger.com/search?searchBar=true&searchQuery=aluminum+fan+blade+6%22
« Last Edit: December 02, 2019, 05:46:56 PM by Slapshot42 » Logged
Pages: 1 [2] 3  All   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!