SMC Discussion Areas
August 20, 2019, 03:37:43 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: vendo 63 help please, can machine  (Read 356 times)
0 Members and 1 Guest are viewing this topic.
blastermc
Newbie
*
Offline Offline

Posts: 5


« on: July 08, 2019, 04:12:45 PM »

I add coins the coil goes into itself and I can not pull out a can,, if I then push down with my finger on the bottom
of the coil where it attaches to the link arm, then it will let me pull out a can and when I close the latch after the can comes out,
everything resets and no can vend,,
any help?
did I reassemble the solenoid bracket wrong?
Logged
blastermc
Newbie
*
Offline Offline

Posts: 5


« Reply #1 on: July 08, 2019, 04:13:59 PM »

here is linkage again with after I push down with my finger
Logged
blastermc
Newbie
*
Offline Offline

Posts: 5


« Reply #2 on: July 08, 2019, 04:15:06 PM »

v63 pepsi can
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5113


This is fine...everythings going to be OK....


WWW
« Reply #3 on: July 08, 2019, 08:49:06 PM »

First you are missing your vending switch assembly, it mounts to where those two loose screws are dangling  (marked by the  blue stars in the picture) but this has nothing to do with your vending problem with the mechanical stack itself.

Second,  you are probably also missing your solenoid return spring that mounts on the back side of the stack it pulls back on the lever that's marked by the orange star & clips on a stepped hook setup on the backside of the stack & pulls back on the lever in the direction of the orange arrow, which in turn puts back pressure on the solenoids plunger ( green star & arrow) so when you trigger the solenoid it pops back to the down" position to allow a can to be selected ( you are basically doing the same motion with your finger/manually)

pull the stack, attach the spring to the point marked by the orange star & attach the other end / hook it to the #1 slot on the tension slots on the rack,

you can only see it from the backside of the rack.
« Last Edit: July 08, 2019, 08:53:18 PM by johnieG » Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220, 221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
Because 11 is louder than 10...
blastermc
Newbie
*
Offline Offline

Posts: 5


« Reply #4 on: July 08, 2019, 09:57:23 PM »

yes the tension is properly hooked up, the switch that is missing, I actually have one from soda jerk works and its too big, it does mount in there
but with that bar that sticks out that's suppose to contact the switch, the new replacement switch is way to big and keeps it closed with no room to adjust the leaf
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5113


This is fine...everythings going to be OK....


WWW
« Reply #5 on: July 09, 2019, 04:18:13 AM »

Regardless of the missing vend switch, if the solenoids plunger ( core) doesn’t return fully to the extended ( down) position after it’s been triggered ( activated) by the coinmech’s electrical pulse, it won’t release the vending links to allow you to pull a can out of the stack.  

 Check the linkage again to see what’s hanging it up & causing it to stick. In the retracted position, also it looks pretty corroded the core could just be hanging up in the coils bore,  it should move freely in & out.
« Last Edit: July 09, 2019, 04:22:50 AM by johnieG » Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220, 221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
Because 11 is louder than 10...
blastermc
Newbie
*
Offline Offline

Posts: 5


« Reply #6 on: July 09, 2019, 06:22:29 AM »

cool thanks, I’ll  clean that up
« Last Edit: July 09, 2019, 05:24:16 PM by johnieG » Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5113


This is fine...everythings going to be OK....


WWW
« Reply #7 on: July 12, 2019, 10:39:30 PM »

So... did you figure it out?  oh
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220, 221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
Because 11 is louder than 10...
cohammer
Soda Jerks
*****
Offline Offline

Posts: 869



« Reply #8 on: July 13, 2019, 12:51:21 AM »

Congratulations on the 5100 post by the way Johnnie G
Logged

Ideal 35 RC
v 23 deluxe
v 39
c 96
c 55 e
C 51 g
C 72
C96
V 27
Westinghouse JR ice chest
Westinghouse standard ice chest
Westinghouse master ice chest
early model Stoner jr.
Stoner theaters
Thanks Jeff
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!