SMC Discussion Areas
November 23, 2024, 04:48:54 pm *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
SMC Discussion Areas > Soda Machines, Coolers & Dispensers > Pre 60's Machines & Coolers (Moderators: johnieG, Jim) > Power consumption, vendo 83
Pages: 1 [2]  All   Go Down
« previous next »
  Print  
Author Topic: Power consumption, vendo 83  (Read 11170 times)
0 Members and 1 Guest are viewing this topic.
Guest
« Reply #10 on: April 21, 2005, 11:28:23 am »
Ok, thanks you very much for the help! I´ll look for a transformer that can deliver about 800 watt.
Logged
sodaworks
Soda Jerks
*****
Offline Offline

Posts: 3532
« Reply #11 on: April 21, 2005, 10:27:24 pm »
Safta,
  I would replace the complete wiring harness and both fan motors. The wire harness cost about 35.00 U.S. and the fans are 26.00 U.S.  It will run more efficiently and you will not have to worry about old rotton wires shorting out and causing a fire. The wiring harness comes with simple instructions. You will not need an electrician. Terry ':drinkers:'
Logged
TERRY@SODAWORKS RESTORATIONS
Lots of Round Top machines
Buy-Sell-Trade-Restorations
Guest
« Reply #12 on: April 23, 2005, 01:43:05 am »
Ok, where can I buy these things?
Logged
loman4ec
Soda Jerks
*****
Offline Offline

Posts: 4768
« Reply #13 on: April 23, 2005, 07:28:46 am »
Not to say that sodaworks is wrong in any way, but if you look over the wiring and it looks ok there is no reason to replace it. If mine is brittle of frayed I replace them on origional machines but for example I am selling a Pepsi vf56 today and I went over it this week and the wiring looked fine so I am keeping it the way it is. As for fan motors. Some people replace them and some people don't. I say if it aint broke don't fix it. A good running fan motor could run for another 50 years, but at the same time it could go out tomorrow. On restored machines I replace them but on an origional If it seems fine I keep it that way.
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5396


This is fine...everythings going to be OK....


WWW
« Reply #14 on: April 23, 2005, 10:09:10 am »
The voltage step-down transformer rated at the correct VA (wattage, technically A.C. electric motor power is rated in Volt-Amps, ie: "VA" ...D.C. power is rated in "watts") but it's not a big deal to refer to it as "watts"....so enough electrical theory 101...

Also be sure your evaporator electric motor & condensor's motor are rated for 60/50 hz (cycles) of A.C. line frequency,
it's 60hz here in the States & Canada, the only reason I mention it is because at 50hz, the motors will consume a little more power & generate more heat (if they're not rated for 50/60hz) & you'll have to take it into consideration in sizing the step-down transformer.  just a thought



 '<img'>
Logged
Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
Guest
« Reply #15 on: April 23, 2005, 12:39:38 pm »
Ok thanks!

And how many VA is 800 watt?
Logged
Skeleton Man
Soda Jerks
*****
Offline Offline

Posts: 692


WWW
« Reply #16 on: April 23, 2005, 01:53:11 pm »
Quote (safta @ April 23 2005,1:39)
Ok thanks!

And how many VA is 800 watt?

800 Watts = 1200VA (approx)

(Watts x 1.414 = VA; VA x 0.7 = Watts)
Logged
sodaworks
Soda Jerks
*****
Offline Offline

Posts: 3532
« Reply #17 on: April 23, 2005, 11:16:06 pm »
Safta,
  You can get the harness and motors from sodajerk works or Funtronics. ':drinkers:'
Logged
TERRY@SODAWORKS RESTORATIONS
Lots of Round Top machines
Buy-Sell-Trade-Restorations
Pages: 1 [2]  All   Go Up
  Print  
« previous next »
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!