SMC Discussion Areas
September 21, 2018, 10:45:33 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Restored Vendo 6 Case Vertical Concerns  (Read 93 times)
0 Members and 1 Guest are viewing this topic.
chuggybear
Newbie
*
Offline Offline

Posts: 22


« on: September 10, 2018, 08:54:46 PM »

Hello Everyone,

I recently purchased this “restored” Vendo 6 Case Vertical and I have a few concerns with it.  I was hoping I could get some advice on how to correct the issues I see.  I bought the machine without seeing it in person and only using photos provided by the seller.  The seller told me that all that was wrong with it was a missing cap catcher that I could purchase online.  Other than that, it was said to be in great working condition.



First, the lower right door panel does not sit flush against the machine.  The left side will sit flush if I push it.  The left side seems to be getting caught on the kick plate when closing.  If I push it towards the machine, it corrects it.  I am wondering if the door is sagging?  Is there anyway to adjust the hinges to line it up better so it doesn’t touch it upon closing.  







Second, it looks like the cabinet breaker trim was installed poorly.  It doesn't line up at some corners and overlaps at others.  It also appears as if an oval washer is missing from the corners that aid in lining up the pieces.  This is especially concerning at the lower front left of the machine as it causes a gap in the gasket, which I believe is contributing to a condensation problem that I will discuss further on.  The 4th picture is a comparison picture of a restored machine by another individual that shows the breaker strips correctly lined up and the oval washer.  Does anyone know what type of washer this requires and where I can purchase it from?





COMPARISON PICTURE


Third, it appears to be missing a plastic breaker strip that should cover this exposed wood behind the bottle door. Also, I am seeing a lot of missing screws here.  Does anyone know where I can purchase this breaker strip and the screws required?  Or if someone can provide the screw type and I can purchase at Home Depot.




Fourth, I am getting a lot of condensation on the bottle door and bottle door gasket.  Is there supposed to be some foam in between the two plates of glass to insulate it?  The current foam between the glass doors is sporadically placed and not continuous.  You can see this in the picture where you can see the white plastic backing on the foam.  As I move my hand from the top of the bottle door to the bottom, I feel the glass get increasingly colder.






Foam stripping with white backing that is not continuous.  


Wood bottle door frame not touching flush at top.


Bottle door hinge missing screw.  Again, if anyone can provide the type of screw needed and dimensions.


Fifth, this Tupperware container is my condensate pan.  I know most of these machines use a bell jar latched by a bracket in the corner of the machine.  I am ok with the Tupperware, but it is filling up completely after 2 days.  The machine is in my garage in Arkansas with a humid climate. However, I have other machines that never require emptying the condensate pan.  I feel as if the main door and bottle door gasket isn’t sealing properly and causing cold and hot air to mix more frequently resulting in more condensate.



Sixth, I am getting frosting on my pipes.  Again, I believe due to improper door seal.





Seventh, based off the previous comparison photo above, I think this door gasket should have been cut out at the hinges.  If so, I think it might improve the door seal and maybe help with the door sag.  I am hoping someone can tell me if this is correct before I cut it out.



Eighth, I can feel cold air leaking from the machine where this gasket isn’t sitting flush.  Also, the bottom of the door panel isn’t flush with the machine as mentioned earlier.  Is there anyway to improve this?



Finally, the bottle door is getting scratched by the head of the screws in the chrome trim.  Is there anything I can do to prevent this from getting worse?  Different screws with flat heads?  





Thanks for any and all help that you can provide me with!  I would love to get the door gasket to seal better, find the breaker trim required, and replace all the missing screws.  Any links anybody can provide to help be buy these things would be fantastic.  
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!