SMC Discussion Areas
March 28, 2024, 05:45:41 pm *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1] 2  All   Go Down
  Print  
Author Topic: Vendo 81 bezels  (Read 7113 times)
0 Members and 1 Guest are viewing this topic.
cokecolaman
Soda Jerks
*****
Offline Offline

Posts: 986



« on: June 28, 2013, 09:49:27 am »

I was wondering what tricks people use to get the coin return and bottle opener bezels put on tightly on a large door 81... Ive tried the pliers with tape on the jaws, but I'm not able to get the bezels on tight enough...any tips would be appreciated.
Logged

VMC Coke 88 (nice original)
VMC Pepsi 81
VMC Orange Crush 81
VMC Squirt 81
VMC Dr. Pepper 81
VMC RC 81
VMC 7up 81 st
Vendo 44 original
Jacobs 56 Pepsi
Cavalier 33
bcharlton
Soda Jerks
*****
Offline Offline

Posts: 1285



« Reply #1 on: June 28, 2013, 09:58:49 am »

I have the same problem.

Brian
Logged

bcexpress

Vendo 39 Original
Cavalier C-51 Restored
Cavalier C-96 Restored (almost done)
GE Double Chiller Restored
Cavalier C-33 7 Up Restored
Vendo 27b Pepsi
Vendo 81b
Westinghouse wd-5 / WE-6
3 Stoner Candy/Theatre/Junior/180
Bastian Blessing Bobtail soda fountain
Jacobs 56 Pepsi
coke_and_stuff
Soda Jerks
*****
Offline Offline

Posts: 3253



« Reply #2 on: June 28, 2013, 10:12:50 am »

I carefully use a flat blade screw driver from the back side and push the tabs in.

Joey
Logged

Collector of nice original paint machines

Vendo 81 B, C, D
VMC 81 Pepsi, 7up, RC, Generic
6CV Coke, RC, Pepsi
VMC 110 RC
Vendo 39
Jacobs 26
Mills 47
Selectivend 64 7up NOS
Plus 30-50 parts and project machines
Funtronics
Soda Jerks
*****
Offline Offline

Posts: 1112



« Reply #3 on: June 28, 2013, 10:27:58 am »

The trick is to put lots of electrical tape on bezel then use a pair of vise grips. Put the large part of vise grip on outer side of bezel and small part of vise grip on tab and squeeze vise grip till tab is flat. You may have to adjust vise grips several times to get the opening just right. Good Luck.
Logged

Rod
Fun-Tronics
cokecolaman
Soda Jerks
*****
Offline Offline

Posts: 986



« Reply #4 on: June 28, 2013, 10:59:30 am »

Thanks!
Logged

VMC Coke 88 (nice original)
VMC Pepsi 81
VMC Orange Crush 81
VMC Squirt 81
VMC Dr. Pepper 81
VMC RC 81
VMC 7up 81 st
Vendo 44 original
Jacobs 56 Pepsi
Cavalier 33
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5869


#1 Soda Jerk!


WWW
« Reply #5 on: June 28, 2013, 01:11:36 pm »

First, I would bend one side of the tabs in half way just to aid a little for that side when it comes time to finish bending them inward.
I utilize a small/medium size "channel locks", otherwise they may not fit into the opening, a good rag and carefully get the outer-most teeth to lock onto the outside of the bezel, then slowly squeeze thus bending the tab inward and upward locking it into place quite well.
Be sure to center the bezel as you continuously monitor the rag position, so nothing gets scratched, and the tightness of the tabs... You might have to go back and forth between the left and right tabs until everything is centered & tight
Logged

My six cents,

Jim

SIGNGUY
Soda Jerks
*****
Offline Offline

Posts: 5442


Collector of Ol Smoothie Rootbeer


WWW
« Reply #6 on: June 28, 2013, 03:12:45 pm »

I do what Rod says, I have a pliers I just use for that purpose.. it's would up with electrical tape to not mar the surface and just position and squeeze.. never had a problem.
Logged

Soda Machine Enthusiast since 1996!
Zerbie
10 Cent Member
***
Offline Offline

Posts: 180


Bob


« Reply #7 on: May 19, 2020, 10:29:54 pm »

 help
This search is the closet I could find with the help I need on my small door Vendo 81B coin return bezel.

I was wondering what folks do for removing and installing the coin return bezel on a small door Vendo 81B? I'm assuming what I have is original? The coin return bezel has four small rivets holding it in place. Before I ruin anything, I'm assuming that the bezel comes off during a restoration process? And then what is the most common way to re-attach them?

1. Try and find small rivets to replicate the original look

2. Use small SS machine screws with a SS nut on the back(there's nut a lot of room on the back side for a nut - it would have to be pretty small nut which may be hard to pair up with the correct size screw diameter for the hole size in the coin door).  

Appreciate your help in advance!
« Last Edit: May 19, 2020, 10:43:47 pm by Zerbie » Logged

Jacobs 56 Restored
Vendo 81D Previous "resturbished"  - New Refurbishment in process
Vendo 81B - restoration in process
VMC Pepsi 81 - in line for restoration
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5869


#1 Soda Jerk!


WWW
« Reply #8 on: May 20, 2020, 10:46:40 am »

Definitely drill the rivets out with 1/8" drill bit and be sure to very slightly enlarge the holes as both processes, chrome plating and the paint/body work, will make the holes small again. A small aluminum rivet will work fine for re-installing the chrome return cup.
Logged

My six cents,

Jim

Zerbie
10 Cent Member
***
Offline Offline

Posts: 180


Bob


« Reply #9 on: May 20, 2020, 06:54:32 pm »

Thanks for the tip Jim! I like your verbiage of "chrome return cup" better than what I was calling it .....a coin return bezel - it makes perfect sense to me now that this part is not a bezel at all because it is all one piece. Any tips/tricks special tool to install and set the the new rivet correctly?
Logged

Jacobs 56 Restored
Vendo 81D Previous "resturbished"  - New Refurbishment in process
Vendo 81B - restoration in process
VMC Pepsi 81 - in line for restoration
Pages: [1] 2  All   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!