|
johnieG
|
 |
« Reply #10 on: January 26, 2013, 01:10:15 pm » |
|
Now the old push-to-start type...
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
BrianS
|
|
« Reply #11 on: January 26, 2013, 01:45:55 pm » |
|
I think I saw a 4-wire switch at Menards in their specialty devices section. I remember thinking that I wish I would have seen them when I was redoing my 81D. Since I didn't need one at the time I didn't look too closely but I recall it having 2 black and 2 blue wires which it what my original switch had. I'll try to stop by and see if my memory is correct or if I was just not paying close enough attention.
|
|
|
|
|
Logged
|
Brian
Vendo 56 - restored
Vendo 81 - in progress
Vendo 39 - in the rough
Rockola 1428 - Original
1959 Williams Pinch Hitter
Wurlitzer 1400
1930 Koken Barber Pole
|
|
|
|
msanborn
|
|
« Reply #12 on: January 26, 2013, 02:02:25 pm » |
|
BrianS: if menards has one, please grab one for me, I looked online, didn't see it. Tks
|
|
|
|
|
Logged
|
Vendo 81
Vendo 39
Pepsi VMC 81
Ideal Slider
Glasco Slider
|
|
|
|
|
|
coke_and_stuff
|
|
« Reply #14 on: January 27, 2013, 12:53:41 am » |
|
Thanks for the links, I got my stock pile refilled. I was down to one left before tonight!
Joey
|
|
|
|
|
Logged
|
Collector of nice original paint machines
Vendo 81 B, C, D
VMC 81 Pepsi, 7up, RC, Generic
6CV Coke, RC, Pepsi
VMC 110 RC
Vendo 39
Jacobs 26
Mills 47
Selectivend 64 7up NOS
Plus 30-50 parts and project machines
|
|
|
|
SIGNGUY
|
|
« Reply #15 on: February 26, 2013, 10:12:11 pm » |
|
Ok I'm confused. I got some new ballast from Funtronics bit says preheat start. So do I need to wire in a starter on this assembly then. And where do I put it and what size do I need?
|
|
|
|
« Last Edit: February 27, 2013, 08:03:51 pm by johnieG »
|
Logged
|
Soda Machine Enthusiast since 1996!
|
|
|
|
Creighton
|
|
« Reply #16 on: February 26, 2013, 11:59:00 pm » |
|
Hope Funtronics chimes in here, cause I have no idea.
Creighton
|
|
|
|
|
Logged
|
|
|
|
|
tkaz
|
|
« Reply #17 on: February 27, 2013, 12:23:07 am » |
|
My local hardware store has a couple switches in stock, about $9 each if I can help anyone out.
|
|
|
|
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #18 on: February 27, 2013, 06:00:29 am » |
|
Ok I'm confused. I got some new ballast from Funtronics bit says preheat start. So do I need to wire in a starter on this assembly then. And where do I put it and what size do I need?
No, "pre-heat" is just the type of ballast it is, it may be used in any pre-heat circuit with a starter or 4-wire switch, just wire it like I showed you in the 4-wire switch diagram. |
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
SIGNGUY
|
|
« Reply #19 on: February 27, 2013, 06:02:21 pm » |
|
Ok so it i don't use a 4 wire switch. And just a two wire is a starter required
|
|
|
|
|
Logged
|
Soda Machine Enthusiast since 1996!
|
|
|
|
