drednot
Newbie
 Offline
Posts: 12
|
 |
« on: June 22, 2012, 11:56:33 am » |
|
Hello,
Does anyone have or know where I could get a door liner for a Cavalier CS-96C square top machine?
Thanks,
Derek
|
|
|
|
|
Logged
|
|
|
|
drednot
Newbie
Offline
Posts: 12
|
|
« Reply #1 on: July 31, 2012, 03:01:50 pm » |
|
I am gonna give myself a bump, because my whole restoration is on hold for a door liner. Anyone have one that I could buy? Sodajerkworks told me they would need a good one to make a pattern for, so does anyone have a good one that they would volunteer to be used to make a pattern for?
|
|
|
|
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #2 on: July 31, 2012, 05:02:31 pm » |
|
should have been here a 1-1/2 years ago when I hauled 6 chassis to the local scrap yard, I post them for parts here but no takers at the time ( sorry to torment you) hopefully someone can pony-up
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
drednot
Newbie
Offline
Posts: 12
|
|
« Reply #3 on: July 31, 2012, 05:10:29 pm » |
|
Thanks,
I just can't believe I may have to junk my machine because of a door liner! I may have to part mine out or haul to the dump!
|
|
|
|
|
Logged
|
|
|
|
|
tkaz
|
|
« Reply #4 on: July 31, 2012, 06:28:52 pm » |
|
I'm in the same position as you with a Vendorlator 90, just need to find a door liner, mine is too beat up. I'm considering having a sheetmetal shop fab up a sheet of textured aluminium which is what some of the Cavaliers used at a point in time.
|
|
|
|
|
Logged
|
|
|
|
|
Creighton
|
|
« Reply #5 on: July 31, 2012, 09:27:43 pm » |
|
Don't junk a machine just because of a door liner. A couple of chunks of foam core from Hobby Lobby/Michael's will work just fine until you can make/find something better.
All the door liner needs to do is hold the insulation in place.
Creighton
|
|
|
|
|
Logged
|
|
|
|
drednot
Newbie
Offline
Posts: 12
|
|
« Reply #6 on: August 01, 2012, 08:11:56 pm » |
|
I know I have seen a Cavalier with a stainless steel door liner, but I can't remember where. I am a pretty good fabricator but I can't imagine making a door liner that matches the plastic one for my particular machine. You would need a worldclass fabricator that has access to a planishing hammer, and a lot of other equipment. I guess I need to just wait and try to find one or try to fab something out.
|
|
|
|
|
Logged
|
|
|
|
|
SIGNGUY
|
|
« Reply #7 on: August 02, 2012, 08:25:37 am » |
|
I guess I dont' see the need to have an exact replica made of the original.. if you have the original, even broken, take it to a sheet metal shop and have them cut one out for you... at least you can put something in place and finish and enjoy your machine...
Goodl Luck!
|
|
|
|
|
Logged
|
Soda Machine Enthusiast since 1996!
|
|
|
|
Blind1968
|
|
« Reply #8 on: August 02, 2012, 01:18:18 pm » |
|
|
|
|
|
|
Logged
|
~ Bryan
|
|
|
|
johnieG
|
|
« Reply #9 on: August 02, 2012, 07:12:35 pm » |
|
Nice set of parts, but he needs the liner for a CS90, this one is a CS64  |
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001... Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
