SMC Discussion Areas
November 26, 2024, 01:40:15 am *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
SMC Discussion Areas > Restorations > General (Moderators: johnieG, Jim) > Shelf Brackets & Plugs - 6 case
Pages: [1] 2  All   Go Down
« previous next »
  Print  
Author Topic: Shelf Brackets & Plugs - 6 case  (Read 8558 times)
0 Members and 4 Guests are viewing this topic.
fabes
5 Cent Member
**
Offline Offline

Posts: 66
« on: September 29, 2011, 04:25:26 pm »
Hey guys, I took my liner out today and obviously need some work done to it.

I had a question about the shelf holders AND plug looking things (don't know what they're called). The shelf holders look like a phillips screwdriver will take them out, but they aren't giving an inch!

How do you take both of them out? and if you do, do you need to replace them or can you reuse them?
« Last Edit: October 18, 2011, 08:32:40 am by fabes » Logged
Thanks for all your help!
-Pete
------------
fabes23@gmail.com
MoonDawg
Soda Jerks
*****
Offline Offline

Posts: 6227
« Reply #1 on: September 29, 2011, 05:16:23 pm »
        For simplicity, why not leave them alone and work around them?
Logged
Glen
fabes
5 Cent Member
**
Offline Offline

Posts: 66
« Reply #2 on: September 29, 2011, 05:20:41 pm »
Glen,
Would you recommend it? My liner looks like this.......





I'm getting a new liner bottom.

Logged
Thanks for all your help!
-Pete
------------
fabes23@gmail.com
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5396


This is fine...everythings going to be OK....


WWW
« Reply #3 on: September 29, 2011, 06:27:04 pm »
Beware! they may be left-hand threaded!!!  try to turn the clockwise to loosen them...
Logged
Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5880


#1 Soda Jerk!


WWW
« Reply #4 on: September 29, 2011, 06:28:39 pm »
Pete,
If the liner has been removed, you should be able to vise-grip each screw from the thread side, clamp on and twist to break them free, then use a Phillips screwdriver from inside the liner to finish removal...
As far as the circular pins, I cannot tell how they are installed... I close-up photo of the back of one of the pins may lead to a solution OR at least how they're installed...
Logged
My six cents,

Jim
collecture
Soda Jerks
*****
Offline Offline

Posts: 6959


Tom
« Reply #5 on: September 29, 2011, 07:38:13 pm »
Quote from: fabes on September 29, 2011, 04:25:26 pm
I had a question about the shelf holders AND plug looking things (don't know what they're called). The shelf holders look like a phillips screwdriver will take them out, but they aren't giving an inch! How do you take both of them out? and if you do, do you need to replace them or can you reuse them?


The manual refers to everything
The Shelf Brackets (20 Qty.) are secured by Phillips Truss Head screws (40 Qty.)
The "Plug Things" are referenced as two pieces - Shelf Support (20 Qty)and Shelf Support Stud (20 Qty) - probably stud rivets. Can you supply a close-up pic of the backside of the stud?

An Impact Screwdriver has proved useful to me in removing difficult screws. Just make sure you apply sufficient pressure so as not to strip the screw head!
Logged
Cav 27, 33, CS-55E-2, 72
S-48 DP
Ideal CC 35, Barq's 55
1930s DP Counter Cooler
Vendo Coin Changers (ea. style - orig w/ stand)
Vendo Junior (rest.), 23 Deluxe, 39D, 44, 56RT, 80SS, 81A (orig), 81D, 6 C.V.
VMC 27, 27A, 81D DP, 110 DP
Westy WC-42-T, WC-44SK, WD-5(2), WB60
Victor C-14
Jim
Administrator
Soda Jerks
*****
Offline Offline

Posts: 5880


#1 Soda Jerk!


WWW
« Reply #6 on: September 29, 2011, 08:15:51 pm »
Quote
An Impact Screwdriver has proved useful to me in removing difficult screws. Just make sure you apply sufficient pressure so as not to strip the screw head!
Just be careful not to dent the liner as you impact the screws!
I would attempt vise-gripping the threaded side of the screw and turn clock-wise to loosen...
Logged
My six cents,

Jim
bubba
Soda Jerks
*****
Offline Offline

Posts: 3021
« Reply #7 on: September 29, 2011, 08:39:02 pm »
Quote from: Jim on September 29, 2011, 08:15:51 pm
Just be careful not to dent the liner as you impact the screws!
I would attempt vise-gripping the threaded side of the screw and turn clock-wise to loosen...


This is the perfect impact tool for that.. I bought one and absolutely love this tool..

http://www.boschtools.com/Products/Tools/Pages/BoschProductDetail.aspx?pid=PS40-2A
Logged
Ken

V-63 -Bottles
2-Cavalier USS-64
VMC ST56B Royal Crown - being built
Vendo HA56C Coke
2-V63C DP
V63C Coke
U-Select-It 5cent candybar machine
BrianS
Soda Jerks
*****
Offline Offline

Posts: 731
« Reply #8 on: September 29, 2011, 10:02:52 pm »
 I had some trouble with some of the screws on my shelf brackets as well.  I found Jim's trick - turning the tread side of the screw with a vicegrips and using a screw driver at the same time to be very effective.  Just don't squeeze the vice grips so tight that you damage the threads.  Found that screws I could not move at all with just a screw driver turned very easy when twisting on both ends. 
Logged
Brian

Vendo 56 - restored
Vendo 81 - in progress
Vendo 39 - in the rough
Rockola 1428 - Original
1959 Williams Pinch Hitter
Wurlitzer 1400
1930 Koken Barber Pole
SIGNGUY
Soda Jerks
*****
Offline Offline

Posts: 5442


Collector of Ol Smoothie Rootbeer


WWW
« Reply #9 on: September 30, 2011, 09:01:01 am »
I have not worked on a 110 for some time, now, but personally I don't think they will interfere with you putting in that new bottom pan.. and if your giong to powder coat the whole tub, I'd just powder with them in?
plus if you get them out, you may have more trouble getting them back in, and pretty sure they are not reproduced.
Logged
Soda Machine Enthusiast since 1996!
Pages: [1] 2  All   Go Up
  Print  
« previous next »
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!