SMC Discussion Areas
April 30, 2024, 07:33:32 am *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Kicking out coins  (Read 5227 times)
0 Members and 2 Guests are viewing this topic.
halehouse
Soda Jerks
*****
Offline Offline

Posts: 2421



« on: January 03, 2010, 04:29:10 pm »

What would make my coin mech kick out coins? It seems to randomly kick on and drop coins. I can sit in the rec room and here it hummmm. Then, ka chink, ka chink, ka chink, out drops the change. I keep trying to reload the mech, but after a while it kicks them out. I have the manual somewhere, but haven't located it yet.

Nice sound effects, huh?
Logged

Vendo 63 Stylestar (Restored)
Glascock Standard
Cornelius 50 Slider (Restored)
tkaz
Soda Jerks
*****
Offline Offline

Posts: 1900

tkaz


WWW
« Reply #1 on: January 03, 2010, 04:52:12 pm »

What kind of mech is it Dan?  It could be the circuit board going awry, have you tried clicking over the inventory switch to see if you can get it to stop?  Otherwise, unplug it for a bit, then plug it back in.
Logged

johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5387


This is fine...everythings going to be OK....


WWW
« Reply #2 on: January 03, 2010, 05:48:08 pm »

sounds like a zener voltage regulator is going on the fritz on the logic board ( coinco 9800 series? )
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
halehouse
Soda Jerks
*****
Offline Offline

Posts: 2421



« Reply #3 on: January 03, 2010, 05:58:25 pm »

sounds like a zener voltage regulator is going on the fritz on the logic board ( coinco 9800 series? )

Yes. Coinco 9800 it is.
Logged

Vendo 63 Stylestar (Restored)
Glascock Standard
Cornelius 50 Slider (Restored)
tkaz
Soda Jerks
*****
Offline Offline

Posts: 1900

tkaz


WWW
« Reply #4 on: January 03, 2010, 07:25:33 pm »

johnieG, is it relatively common to rebuild the logic boards?  If its the one diode, it seems like an easy replacement.  Have you done these before? 
Logged

johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5387


This is fine...everythings going to be OK....


WWW
« Reply #5 on: January 03, 2010, 07:51:01 pm »

then the logic board is faulty, it controls the 12-volts that drives the payout motor, when it goes bad, it will cause the coinmech to turn into a slot machine, or cause it to give out "ghost" payouts, it will also cause the coinmech to give incorrect change. time for a repair.
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 5387


This is fine...everythings going to be OK....


WWW
« Reply #6 on: January 03, 2010, 07:56:34 pm »

johnieG, is it relatively common to rebuild the logic boards?  If its the one diode, it seems like an easy replacement.  Have you done these before? 

not as simple as it appears, the problem is when the zener diode goes bad,  it usually destroys multiple components on the circuit board, & yes I have been repairing these units for about 10 years now, ( and no I won't divulge my my hard-earned trade secrets  blush)
Logged

Spoon-feeding Newbies since 2001...Wink
Yeah..220,221 whatever it takes.
Remember, all it needs is a shot of Freon!
The Vendo V-83 is the '59 Edsel of the coke machine world. ;p
Spray painting does NOT restore a compressor
11 is louder than 10...
"Hope" is good, but it's not an action plan.
halehouse
Soda Jerks
*****
Offline Offline

Posts: 2421



« Reply #7 on: January 03, 2010, 08:47:40 pm »

not as simple as it appears, the problem is when the zener diode goes bad,  it usually destroys multiple components on the circuit board, & yes I have been repairing these units for about 10 years now, ( and no I won't divulge my my hard-earned trade secrets  blush)

So, would you recommend having that repaired, or replacing the mech?
Logged

Vendo 63 Stylestar (Restored)
Glascock Standard
Cornelius 50 Slider (Restored)
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!