Home | Help | Login | Register |
1
Soda Machines, Coolers & Dispensers / Post 60's Machines & Coolers / Re: Vendorlator VF-148-bb won't drop soda
on: Today at 07:27:28 am
|
||
Started by FOWL1 - Last post by FOWL1 | ||
OK, so yeehaw, I finally got my VF-148-BB to vend properly. I installed the motor and set the timing according to the book. I loaded the machine several time and it just wouldn't work the way it was supposed to. I unloaded it and duct taped the sold out levers down so it thought it was loaded. I left the door open, dropped a quarter and pushed a selection. What I realized is that the button on mine needs to be held until the soda drops. I noticed the solenoids were hanging up when the button was pushed and released quickly. I also noticed, after several operations, the pivot pins were in the wrong location to operate.(they were almost all the way up) I took out the 2 back bolts holding the motor and loosened the front one. I moved the bar with the pivot pins down to the proper location.( which was supposed to be almost all the way down) I swung the motor back up, not worrying about the timing, bolted it back in tightly and voila(that's French meaning whoop there it is) the machine is vending every time as it is supposed to. Thanks to JohnnyG for the pictures. They are what got me to thinking about the position of the pivot pins. Thanks to everyone for helping me through this. Now the wife is no longer saying just get rid of it if it doesn't work. I knew it had to be something very simple, but my simple brain just couldn't get it. It's working well now so we're good to go. Thanks again for this forum. Hopefully this explanation will help someone else with this type of machine.
|
2
on: Yesterday at 10:55:06 am
|
||
Started by johnieG - Last post by johnieG | ||
Thanks..because now it's SOLD! shipping it off to its new owner.
![]() |
3
Soda Machines, Coolers & Dispensers / Pre 60's Machines & Coolers / Re: Help in identifying this machine for a friend
on: April 05, 2025, 06:29:09 am
|
||
Started by pepsi man - Last post by Jim | ||
The machine pictured is Cavalier CS-96; however, there is no adjustments for the cabinet door hinges or door gap. Sometimes, when the liner/gasket are installed on the cabinet door and it's not completely flat, the door can/will develop a slight "warp" that can keep the door from sealing properly on one area of the gasket. Hard to determine from the photos, ensuring the right size gasket is important as this could cause an improper fit. One other thing to check is the screws used ti install the liner/gasket and ensure they are all tightened down properly. If the screw head is too big, it will impede on the gasket space causing an issue as well.
Hopefully helpful ! ! ! |
4
Soda Machines, Coolers & Dispensers / Post 60's Machines & Coolers / Re: Vendorlator VF-148-bb won't drop soda
on: April 03, 2025, 03:01:00 pm
|
||
Started by FOWL1 - Last post by FOWL1 | ||
I know this post is old, but I just had time to work on the VF-148-BB. I have the timing set correctly, but I'm still having an issue wit hthe dropping of the sodas. The first time it dropped 2, then on a different selection dropped nothing and the other selections nothing. At this point, I'm wondering if I'm loading it correctly. The schematic picture shows if the screw is on the right side in the site, load the front first. Likewise if the screw is on the left side in the view, load the back first. I've done that several times. I'm wondering if the bar that runs from front to back needs to be set in the middle of whichever one is being loaded. The bar flops from side to side and I'm wondsering if the column that is loaded needs to have the can sitting on top of that bar instead of the bar being set to the side it flops to when loading. Would anyone have any idea about it? My wife is to the point of telling me to get rid of it. It gets cold and stays cold. I'm sure it has to be something very simple to get it to vend. Please help before I have to get rid of it.
|
5
Soda Machines, Coolers & Dispensers / Pre 60's Machines & Coolers / Help in identifying this machine for a friend
on: April 03, 2025, 02:28:23 pm
|
||
Started by pepsi man - Last post by pepsi man | ||
Hello everyone, been a long time since I've been around. Hope all is well, I have a gentleman who is having some issues with a coke machine and I'm trying to help him out.
He states the door isn't sealing up on the latch side . It makes contact on the hinge side and he has tried adding washers to the hinge side which then causes the latch side to not catch. Which is causing it to run all the time. States the door gasket is new but the door seems warped? I'm wondering if it has the wrong gasket on it. I can't place the make and model on this machine, is their a service manual that shows door adjustments ect? Here are the Pictures I've gotten from him any advice and help you all can give would be great. Thanks much. |
6
on: March 29, 2025, 08:12:14 pm
|
||
Started by RetroPetro - Last post by RetroPetro | ||
Hi Johnie, thanks for your reply. I just picked up the machine and figured I'd start my search here. I am not on facebook.
I tried posting pictures here, but was not able to. Possibly they were too big. I will be selling it, and will offer to members here first. I am located in North Jersey west of Manhattan near I-287. |
7
on: March 29, 2025, 03:54:25 pm
|
||
Started by johnieG - Last post by Jim | ||
Very Nice! Good Luck with the sale!
|
8
on: March 29, 2025, 01:24:05 pm
|
||
Started by johnieG - Last post by johnieG | ||
Fully restored Vendo refrigeration system, will fit V63, V90, V125, & others all powder-coated components & new electricals, wiring, motors, T-stat. Converted to R134a... $600 shipping not included...read details in link...also listed on Facebook marketplace...Note: people keep asking, but, No, I don't sell parts.
Link; https://www.facebook.com/marketplace/item/478791891788547?ref=search&referral_code=null&referral_story_type=post&tracking=browse_serp%3Ac1d973a2-427c-4747-8b81-de3a1d5073b0 |
9
on: March 28, 2025, 10:10:22 am
|
||
Started by RetroPetro - Last post by johnieG | ||
A rare machine & literature will be a toughy... but hopefully someone somewhere has some documentation. have you tried some of the soda-museums? Also you can post on the facebook classic soda machines & Vintage soda machines groups to cast a larger net (so to speak)
|
10
on: March 21, 2025, 08:50:01 pm
|
||
Started by RetroPetro - Last post by RetroPetro | ||
Hello, looking for photo(s) or sales/service literature showing a Lyon 200 vender machine.
Thanks in advance for any help. |