SMC Discussion Areas

The Coin Return => Tutorials & Tips => Topic started by: SIGNGUY on March 18, 2008, 01:04:08 pm



Title: Another Option for Easy ONE MAN liner installation
Post by: SIGNGUY on March 18, 2008, 01:04:08 pm
I learned this trick a few years back, and now that I have some machines I'm working on ... was able to photograph it. The Cardboard trick as demonstrated on another post works great too, but this is easy as well and only requires one person, a roll of painters tape and your machine to be restored.
1)Lay the machine on it's back, cut and lay in insulation, sides first. Before putting the back side insulation in, take a roll of blue 3m Painters tape (works best for me and won't damage paint). Stick one end to back of machine, as close to the side as you can, pull the tape up and compress the insulation to the side and pull tape around the side and fasten to outside of machine. Do this all around sides, spaced out around 4 inches or so apart... Lay in your back side insulation, which will hold the back of insulation in place.
2)grab the liner and slowly work it into the machine.. let the air escape through the holes in the cabinet that are already drilled for the condensor... do this slowley and don't force it, just work it in by applying pressure....
3) it should slide right in and insulation should remain in place as long as your tape on outside of machine holds...
4)once the liner is nearly seated properly... simply grab the outside peice of tape from edge, lift off and pull straight up and out and it will peel right off and leave insulation in place.
5) finish installing liner with spacers and such and walla, your done... see photos.. hope this helps.


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: BrianB on March 18, 2008, 02:14:48 pm
Awesome pic's. It's great to be able to add this to my "toolbox", Thanks!


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: Pat Pixley on March 18, 2008, 02:37:21 pm
That is a great little trick , I will be using that on my next projected :smile:
 Plus I think this would work alot easier on the upright machines.
 Just a question did you lay something under the machine ??


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: SIGNGUY on March 18, 2008, 03:23:56 pm
Just a question did you lay something under the machine ??

 :darn: That's why it's all scratched up on back??? hmmm  :biggrin: No, I laid a blanket down on the floor first then just laid it on it's backside...


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: Pat Pixley on March 18, 2008, 03:32:41 pm
: No, I laid a blanket down on the floor first then just laid it on it's backside...

 Sorry it looked like paper :blush:.


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: Chedki on March 18, 2008, 06:11:26 pm
Great tip ! Are all insulations for soda-pop machines the same? I have a Royal Crown Cola Ideal 55 slider that I will be restoring in the near future. It probably will need to have new insulation installed. So, what kind is needed for this particular machine?


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: Yarochrehc on March 18, 2008, 07:34:47 pm
That's a great idea as well as the cardboard! :biggrin:


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: collecture on March 18, 2008, 11:05:38 pm
That is pretty slick John!
Sometimes it is difficult to get a friends' help right when you need it, so it is always great to easily be able to do things yourself


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: SIGNGUY on March 19, 2008, 09:05:26 am
Great tip ! Are all insulations for soda-pop machines the same? I have a Royal Crown Cola Ideal 55 slider that I will be restoring in the near future. It probably will need to have new insulation installed. So, what kind is needed for this particular machine?
I am not certain about all machines, but I've used R19 unfaced for my machines, the width works well for the cabinet size and it fills nicely..
Before you dig into that SLider... read someo other posts on SMC here and make sure you know what your getting into... That is one of the hardest machines to restore, due to the cooling system coils inside the walls of the machine.
Good luck, Thanks for checking in, and welcome to SMC!


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: loman4ec on March 19, 2008, 09:29:49 am
Signguy, That is a fantastic idea! That will work much better than the cardboard.


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: Jim on March 19, 2008, 07:31:13 pm
Thanks for sharing John ! ! !
Great Tip ! ! !


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: MoonDawg on March 19, 2008, 07:40:43 pm
       Do these great tutorials get saved somewhere for future restorers?


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: Jim on March 19, 2008, 08:25:09 pm
They get Pinned so each one remains at the top of the thread list...


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: sodaworks on March 25, 2008, 03:50:50 pm
John,
This is the same way I've been doing it. I've tried the cardboard trick when it was posted but for me this works much better.


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: scalebowler on July 16, 2010, 02:41:03 pm
Just tried it last night and it did work really well. I did have to have one other person help me move the liner just because I was woried about dropping it just slid in and the tape all came out.


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: Creighton on July 16, 2010, 03:37:11 pm
Dang SB,
That thread was two years old. Glad it worked and thanks for bring it back up for those of us that can't recall what we had for breakfest :-)
Creighton


Title: Re: Another Option for Easy ONE MAN liner installation
Post by: sdj544 on April 27, 2020, 01:14:44 am
Thank you, thank you, thank you!
Glad I saw this tip.
I’ve used cardboard on bigger machines (V39, Cavaliers) and had no problem but just redid a VMC 27 and can’t believe how easy it went. No way with how little space there was around the liner would I have been able to use cardboard. Plus with the curve at the top you just can’t make cardboard do what you want.
Thanks!
-Steve