Title: 110 vendo wiring diagram
Post by: on February 04, 2003, 09:20:22 pm
need a wiring diagram for a 110 vendo.wiring was rotten and broken off at terminals at junction block,clix on switch et'c.if anyone can help please do.live in michigan and have not been able to get a technician to come look at it.too much contstruction going on. they will talk on phone but don't want to travel to the country to work on.
Title: 110 vendo wiring diagram
Post by: johnieG on February 04, 2003, 10:30:56 pm
Here's a basic wiring diagram, I'll copy my V110 schematic when I get a chance...hope it helps you get started 
Title: 110 vendo wiring diagram
Post by: MoonDawg on February 04, 2003, 11:03:55 pm
Johnie's diagram is right on, but if this confuses you, and this is your first time, I suggest ordering a new wiring harness from one of the suppliers on this site. When you recieve it, refer back to this diagram and I'm sure you will understand, and save a bundle of money on a service call.
Title: Re: 110 vendo wiring diagram
Post by: VMAXMAN on February 10, 2011, 11:30:52 pm
old topic I kknow...but what is a klicket and what does it look like?
rewired my 110 and when I turn up the thermostat nothing happens....the thermostat according to the picture is wired from both sides to the neutral?
rewired my 110 and when I turn up the thermostat nothing happens....the thermostat according to the picture is wired from both sides to the neutral?
Title: Re: 110 vendo wiring diagram
Post by: Jim on February 10, 2011, 11:44:22 pm
It's a thermal overload protection
Title: Re: 110 vendo wiring diagram
Post by: johnieG on February 11, 2011, 12:26:42 am
old topic I know...but what is a klicket and what does it look like?
rewired my 110 and when I turn up the thermostat nothing happens....the thermostat according to the picture is wired from both sides to the neutral?
rewired my 110 and when I turn up the thermostat nothing happens....the thermostat according to the picture is wired from both sides to the neutral?
The Thermostat serves the same function as a light switch, ( but it's the thermal sensing bulb that turns it "on") with that in mind, it's wired in series with the "hot" side of the line going into it & then it passes that "switched-hot" along to the compressor's start-run relay/terminal #2, then the common terminal returns through the "Klicket"/thermal overload device ( think as it as a circuit breaker) & back to the neutral side of the line completing the circuit.
Physically it looks like a small round black plastic cylinder about the size of a plastic soda bottles screw-off top with two electrical terminals sticking out of the top, with one side having a short black wire & terminal attached that fit onto the "common" pin-terminal of the compressor, & the other having a screw-terminal or a push-on type terminal to attach to the neutral side of the wiring harness. it's often held physically to the side of the compressors main body by a flexible spring-type of fastener just above or along side of the compressor's main pin-terminals, and inside the usual plastic protective wiring cover on the compressor.
Also note that some machines put the thermostat in series with the neutral side of the line feeding the compressor, but it serves the same purpose as listed above.
Title: Re: 110 vendo wiring diagram
Post by: VMAXMAN on February 11, 2011, 07:49:46 pm
this is what I have...hot from wall goes to top....neutral from wall goes to bottom...right?
and the thermostat goes to hot where?
and the thermostat goes to hot where?
Title: Re: 110 vendo wiring diagram
Post by: VMAXMAN on February 11, 2011, 09:37:28 pm
nm....got it.... the evaporator motor isnt running tho (thats what sits under the shelves...right?)
when I take the wires for it and plug it into electric it SHOULD start....right?
when I take the wires for it and plug it into electric it SHOULD start....right?
Title: Re: 110 vendo wiring diagram
Post by: johnieG on February 11, 2011, 10:18:19 pm
yep, the evap' motor runs 24/7
Title: Re: 110 vendo wiring diagram
Post by: VMAXMAN on February 11, 2011, 10:24:16 pm
Ya....its shot....spins by hand but wont run!
I ordered a new one.
thanks guys!
I ordered a new one.
thanks guys!
Title: Re: 110 vendo wiring diagram
Post by: VMAXMAN on February 15, 2011, 12:26:58 am
ordered one from SJW plus a few other items...got them today!
wow...fast shipping!
Installed it...man this thing runs quiet!
running it at a cool 32 deg.
wow...fast shipping!
Installed it...man this thing runs quiet!
running it at a cool 32 deg.