|
Title: Ideal Slider - Wiring Post by: ZMonet on December 02, 2006, 08:19:53 am I thought I would tackle assessing where my Pepsi Ideal 55 Slider project is at and wanted to see if I could get the compressor/fan/thermostat working. I should have planned better though because once I took a look at it, I'm thoroughly confused. I have a wiring harness (see pic) and although the main plug line is in horrible shape, the rest of the wiring seems ok. I'll probably replace that too, but how do I replace the main power running into the first housing? My confusion is in the fact that there are three wires running to the first box, not two like I expected. Since this doesn't have a ground, I don't know what the third wire is. Can anyone help tell me what I need to do to replace the last run using the harness? I've done plenty of socket/switch wiring before, but never anything like this. Thanks in advance.
Title: Ideal Slider - Wiring Post by: ZMonet on December 02, 2006, 08:45:21 am I now see there is a ground, which makes this much less confusing, but I'd still like some advice on how to best use the connectors on the new harness to connect into the old wiring (after the junction "box"). I'll likely replace all the wiring, but I just want to see what is working and what isn't working for now. Two more pictures to follow.
Title: Ideal Slider - Wiring Post by: collecture on December 02, 2006, 09:08:16 am I do not own a slider, but the harness looks pretty standard. Even though the rest of the wiring only has two leads, the line cord always has three. The ground wire is usually attached to the compressor deck. Most of the time, the junction block mounting bolt is also used to secure the ground wire.
Title: Ideal Slider - Wiring Post by: ZMonet on December 02, 2006, 10:06:50 am Thanks Collecture. I guess my confusion is over where the existing wires connect into the wiring harness. The way I see it, I need to connect two wires to the thermostat and two wires to the compressor. I'm unclear where these four wires connect into my wiring harness. I'm probably making this more complicated than it needs to be, but can someone tell me how the 4 wires connect to the new harness? My assumption is that the harness has a number of connections that aren't needed.
Title: Ideal Slider - Wiring Post by: davethebirdman on December 02, 2006, 10:33:04 am Have you got a wire that would be used for a lighted bottle door in amongst it all??
Title: Ideal Slider - Wiring Post by: collecture on December 02, 2006, 11:03:34 am QUOTE Have you got a wire that would be used for a lighted bottle door in amongst it all?? No bottle door in a slider Dave! There could possibly be a wire to a coin mech heater, but I would disregard that if there. Josh, I've wired many upright machines and suppose the slider is no different; however, I will let somebody more knowledgable about sliders respond instead of steering you wrong. I am sure somebody will chime in soon. Title: Ideal Slider - Wiring Post by: davethebirdman on December 02, 2006, 11:36:39 am I was just thinking that he might have got himself a generic wiring harness and
the wire was spare. I had that problem with a V-39. I couldn't work out why I needed the extra lead. Dave Title: Ideal Slider - Wiring Post by: ZMonet on December 03, 2006, 11:51:29 am This might be a real stupid question, but how do I get the wires I cut to fit into the wiring harness? Do I use a pair of crimpers? I looked at the hardware store for connectors I could attach to the wire ends, but couldn't find anything that would then fit into the harness module.
Thanks guys. Title: Ideal Slider - Wiring Post by: David D on December 03, 2006, 04:12:27 pm I don't think you have the correct wiring harness. I've replaced the wiring on my Glasco slider and it was pretty straight forward. I purchased a standard wiring harness from one of the forum sponsors, I believe it was sodajerkworks.
Here's a picture for reference, note the harness has the terminal block included for the compressor plug. Thanks- Title: Ideal Slider - Wiring Post by: ZMonet on December 03, 2006, 04:19:57 pm Thanks Duchon. I think it is a generic harness, but wires should still go into it. I'm just unsure how they attach. As an aside, Duchon, did you add the wheels to the slider yourself?
UPDATE: I just connected the wires into the harness, but they aren't in their solid and I would be better off using wire nuts based on the way it is currently set up. I'm amazed that the fan actually came on. Sadly, it is too cold outside right now to see if the compressor is actually cooling the unit. Anyway, any help on a more permanent solution for attaching the cut wires to the harness would be appreciated. Title: Ideal Slider - Wiring Post by: BryanH on December 06, 2006, 10:53:43 pm When I started tearing mine apart I had a similar question... Couldn't find the post but here's the diagram I drew.
Title: Ideal Slider - Wiring Post by: MoonDawg on December 07, 2006, 11:02:35 am Mr Z. I think the answer you are looking
for is "crimp terminals" They are small #8 rings that crimp to the end of your wire. The screw through them. Duchon, may I give you and the group a word of advice? The power cord going ito the wall outlet has a VERY high chance of getting snagged while moving as we all know. A small clamp is normally installed at the factory and screwed into the machine. This clamp absorbs the strain instead of the j-box. Title: Ideal Slider - Wiring Post by: ZMonet on December 26, 2006, 10:55:17 am Thanks everyone. I'm off to Radio Shack today to pick up the crimp terminals
Title: Ideal Slider - Wiring Post by: aspbear1 on December 26, 2006, 06:07:16 pm I dont know if this is the answer for the extra wire but some of the Ideal 85's have a switch on the lid that shuts the compressor down if the lid is opened. The Nesbitt's that I am working on right now has that type of switch. It is spring loaded and located in the lid hinge.
|