|
Title: Change returns Post by: on October 30, 2002, 06:51:38 pm I have an old Cornelius pepsi machine to restore. I have it set for 5 cents. when i drop in money it returns the change. It has been tested and is a working coin mechanism. any suggestions? All other mechanism's work and when coin mechanism is by-passed, pop does drop.
Title: Change returns Post by: johnieG on October 30, 2002, 08:20:09 pm I assume this is an upright machine with an electronic changer and not a Corneluis slider? do you mean it gives you back change for your nickle? or that it returns your nickle to you? and then it vends?
Title: Change returns Post by: on October 31, 2002, 12:30:40 am it is an upright and it returns the nickel you put in and does not vend.
Title: Change returns Post by: johnieG on October 31, 2002, 08:48:24 am if the mech has been tested and is good then unplug the mech's jones plug & check for 115 Volt AC @ pin #6 to ground,this is the C.R.E.M. control line input ( coin return electro-magnet) if they aren't getting power from the female socket pin#6, then the mech will reject all coins. (I'm assuming it's a Coinco 7800 series mech)
Title: Change returns Post by: on November 01, 2002, 03:18:12 pm i checked the voltage at pin #6 and all i get is 52 volts. thanks for the help.
Title: Change returns Post by: johnieG on November 01, 2002, 06:57:16 pm Yea that would do it! just to be sure double check the voltage reading between pins 2 & 6 (6 will be the hot one )
if its still low then you've got something dropping the voltage to pin #6 probably a dirty connector in the door harness or a corroded wire. Title: Change returns Post by: on November 02, 2002, 12:09:29 am thanks for the help
Title: Change returns Post by: on November 03, 2002, 01:33:49 pm I checked the wire at pin #6 and it is only about 3" long. It goes to what i would call a rely switch. I checked the voltage there and it is the same. Is it possible the switch needs to be replaced?
Title: Change returns Post by: johnieG on November 03, 2002, 09:34:55 pm Hmmm I'll need more info, so is this relay switch attached to the housing that holds the plug? can you post a picture of this switch? if your socket were wired the opposite of the diagram that would put you on pin # 5 instead, which goes to the "correct change only" lamp, (which in turn may be controlled by a relay on some models), how old is this machine? 60's or 70's? and what is the model/make of your coinmech?
Title: Change returns Post by: Jim on November 03, 2002, 10:10:48 pm It sounds like it's similar to a late 50's Vendo 80 or 144 where the jones plug socket is right on top of the vend relay...
Maybe he could momentarily jump a wire between #1 and #3 to see if the machine will vend... As far as the voltage on #6 only being 52 volts, thats strange... What model Cornelius is this? Title: Change returns Post by: on November 04, 2002, 10:10:29 am have not been able to find out what year or model, new to this. pics to follow.
Title: Change returns Post by: on November 04, 2002, 10:12:44 am another pic
Title: Change returns Post by: on November 04, 2002, 10:20:55 am if i jump #1, #3 & #7, the machine will vend without the mech. the problem is it vends until all soda is dispenced. that is why i'm trying to use the mech.i have an idea it may be the orange wire not sending enough voltage, this is what i'm checking next. thanks steve
Title: Change returns Post by: on November 04, 2002, 11:24:44 am of the 12 wires that come up the door to the junction box, only 3 areconnected inside, the rest continue on. the green wire connects to #2 pin on the plug which is hot. the orange wire goes to the switch and the yellow wire goes to #1 pin on the plug and is neutral. the white connector to the left of the plug is not connected to anything.
Title: Change returns Post by: johnieG on November 04, 2002, 01:41:18 pm you should only need to connect pins 1 & 3 to trigger a vend cycle, 7 is normally used by the vending rack to block acceptence of coins during a vend cycle. I'll double check my Coinco manual when I get home tonight...JohnieG
looks like you have a Coinci 7800-A model changer, that helps to know which model you have! Title: Change returns Post by: johnieG on November 04, 2002, 04:49:10 pm O.K. heres a new diagram , if you just wire a small switch (normally open) across pins 1 & 3 without the coinmech plugged in the machine should vend free-play (some machines use pins 2 & 3)
|