Title: Dixie narco model 300
Post by: on October 15, 2005, 11:33:02 am
I just came into possession of a dixie narco model 300/175-5. Some parts are missing from the door panel; the whole coin mechanism behind the coin slot down to the coin return, The lock, the bottle cap capture box(which is easily fixed), the wiring schematic on the back panel of the door, and the most important piece of all a power cord. I have looked around and found some parts that I could purchase but some of the bigger pieces I can not find. Can anyone help me since I am new to restoring? Here is a picture of the unit.
Title: Dixie narco model 300
Post by: dr galaga on October 15, 2005, 07:28:21 pm
Welcome aboard!
Coin mech: johnieG sells them and you can find them on ebay.
Lock: try one of the supporters (advertisers) of the site. Their ads are at the top of the page or try ebay.
Power cord: local hardware store. Buy a nice high amperage one and not a cheap one!
Schematic: This might be a tough one. Try the advertisers for one.
Stick around a while and let's see some picks of the missing parts inside!
Coin mech: johnieG sells them and you can find them on ebay.
Lock: try one of the supporters (advertisers) of the site. Their ads are at the top of the page or try ebay.
Power cord: local hardware store. Buy a nice high amperage one and not a cheap one!
Schematic: This might be a tough one. Try the advertisers for one.
Stick around a while and let's see some picks of the missing parts inside!
Title: Dixie narco model 300
Post by: johnieG on October 15, 2005, 09:17:00 pm
Arrgh! welcome aboard matey! ( Opps, too much Sponge-Bob with my 7 year old I guess! 
) Nice machine & welcome to the site, you're in luck (sorta) I just picked up a DixieNarco 312/180-6 7up machine this Friday, they are very simular machines (Yea-Yea , I know, I know I'll post you lubbers' some pics soon enough 
) I had to drill the lock, but I got a coinbox full of quarters for my troubles! ($26.50!) these vendors are able to vend either bottles or cans, if yours has the back-spacers in the rear of the vending columns, it was originally setup for bottles. yours has the capacity to vend 300 cans or 175 bottles/5 selection-columns.
As for coinmechs, any 120 volt AC/ single price coinmech should fit, I just install a Coinco S75-9800/B in mine & it works great,
I found some replacement parts at this site...VEII on the web, just enter "Dixie Narco" under their search window here's a link, they've got buttons, coinbezels, & vending motors for Dixie Narcos not much, but it's a start, also check with used/vending machine liquidators on Ebay, DN's were fairly popular & many parts are still around. oh & here is the link...
http://www.veii.com/
) Nice machine & welcome to the site, you're in luck (sorta) I just picked up a DixieNarco 312/180-6 7up machine this Friday, they are very simular machines (Yea-Yea , I know, I know I'll post you lubbers' some pics soon enough ) I had to drill the lock, but I got a coinbox full of quarters for my troubles! ($26.50!) these vendors are able to vend either bottles or cans, if yours has the back-spacers in the rear of the vending columns, it was originally setup for bottles. yours has the capacity to vend 300 cans or 175 bottles/5 selection-columns.As for coinmechs, any 120 volt AC/ single price coinmech should fit, I just install a Coinco S75-9800/B in mine & it works great,
I found some replacement parts at this site...VEII on the web, just enter "Dixie Narco" under their search window here's a link, they've got buttons, coinbezels, & vending motors for Dixie Narcos not much, but it's a start, also check with used/vending machine liquidators on Ebay, DN's were fairly popular & many parts are still around. oh & here is the link...
http://www.veii.com/
Title: Dixie narco model 300
Post by: johnieG on October 15, 2005, 09:38:25 pm
Title: Dixie narco model 300
Post by: glassbottlesrule on October 15, 2005, 11:27:39 pm
That's a good website. Thanks for the Link
Title: Dixie narco model 300
Post by: johnieG on October 17, 2005, 07:36:32 pm
As promised, here's my Dixie-Narco 312/180-6 /7up a little dirty, but it'll clean up nice, just spilt soda all over, yuk! .,
and here's the Westinghouse standard wet cooler chassis, note the channel for the cooling lines & water circulation motor, this is one of the few I've found that still hase the brass-ID tag still attatched, you have to admire that Pre-WWII steel, man it holds up to abuse! it's a nice solid chassis, it'll need a set of lids, I'm going to replace the liner with stainless & and I think I'll convert it to forced air/evaporator-cooling (nobody ever wants to buy a "wet" chest cooler.) funny thing that it has a Dr. Pepper crown-puller can't really see it in this pic. but it does say "good for life" in the tail of the "D"
.,and here's the Westinghouse standard wet cooler chassis, note the channel for the cooling lines & water circulation motor, this is one of the few I've found that still hase the brass-ID tag still attatched, you have to admire that Pre-WWII steel, man it holds up to abuse! it's a nice solid chassis, it'll need a set of lids, I'm going to replace the liner with stainless & and I think I'll convert it to forced air/evaporator-cooling (nobody ever wants to buy a "wet" chest cooler.) funny thing that it has a Dr. Pepper crown-puller can't really see it in this pic. but it does say "good for life" in the tail of the "D"
Title: Dixie narco model 300
Post by: johnieG on October 17, 2005, 07:46:33 pm
Now the Westy' pics
Title: Dixie narco model 300
Post by: johnieG on October 17, 2005, 07:51:10 pm
Id plate, & channel
Title: Dixie narco model 300
Post by: johnieG on October 17, 2005, 07:58:08 pm
the Dr. Pepper crown puller.
Title: Dixie narco model 300
Post by: Creighton on October 17, 2005, 07:59:45 pm
Thats very nice JohnieG!! The ID tag reminds me of a Microsoft end user agreement where Microsoft is the every third word :-)
Creighton
Creighton
Title: Dixie narco model 300
Post by: BryanH on October 18, 2005, 12:50:46 pm
| Quote (johnieG @ Oct. 17 2005,5:36) |
| and I think I'll convert it to forced air/evaporator-cooling (nobody ever wants to buy a "wet" chest cooler.) |
Johnie - how do you do this? As you know I'm sitting on a 1940's GE wet (maybe and/or dry) cooler that has a similar setup.
Title: Dixie narco model 300
Post by: glassbottlesrule on October 18, 2005, 03:08:43 pm
Pat Pixley has(had) a Vernor's Ideal 55 that this was done to IIRC. I can't remember seeing the pictures though(hint Hint). It shouldn't be to hard. I was going to do it to an Ideal slider I had but I got bored and sold it before I aquired all the parts. I just hate the cooling systems in the smaller Ideals, anything that has to be cracked open to get out is no fun to me.
Title: Dixie narco model 300
Post by: on October 21, 2005, 12:05:17 am
Thanks for the help. I did get the plug put in and so far it all works so now I need to work on the interior. There on the burst door is a relay switch with another plug next to it but whatever was supposes to be there isn’t and I believe that is where the coin mechanism should be plugged in. I don’t know since I don’t have a schematic to compare to what I’m looking at. Does anyone know what switch I need to convert the machine over to allow us to just push the button and it dispenses without the use of money until I can get the coin mechanism fixed? 
Title: Dixie narco model 300
Post by: on October 21, 2005, 12:06:00 am
Besides that I wanted to also say that people so far who claim to have manuals for the model turn out not to. So if anyone comes across the manual for the 300/175-5 dixie-narco please let me know.
Title: Dixie narco model 300
Post by: dr galaga on October 21, 2005, 10:06:13 am
| Quote (dickspade @ Oct. 21 2005,1:05) |
| There on the burst door is a relay switch with another plug next to it but whatever was supposes to be there isn’t and I believe that is where the coin mechanism should be plugged in. |
Does it have 8 slots in it (like the picture below)? If so, then it is for the coin mech. Specifications for the switch are on the picture.
More information at: Free play switch once more.