SMC Discussion Areas

Soda Machines, Coolers & Dispensers => Post 60's Machines & Coolers => Topic started by: on August 02, 2005, 03:32:22 am

Title: Vendo 63 cooling system schematic Post by: on August 02, 2005, 03:32:22 am I have a vendo 63, that I need the cooling system schematic for (how the compressor is wired to wall power,fan, blower etc) , and I can't seem to find one anywhere. All the schematics I can find are for the front and coin area. Can anyone help? Thanks Robert Title: Vendo 63 cooling system schematic Post by: on August 02, 2005, 08:59:12 am Welcome to the board.  I'm no help, but I'm sure that someone here will be able to help you. Title: Vendo 63 cooling system schematic Post by: Creighton on August 02, 2005, 01:07:59 pm Welcome Robert! Have you tried calling the sponsers listed on the main page of this board? Great folks and they should be able to help. Creighton Title: Vendo 63 cooling system schematic Post by: dr galaga on August 02, 2005, 03:11:58 pm The manuals that I have seen only have the vending wiring (just like giftedone says).  If anyone has one, it would probably be johnieG (he seems to have a diagram for everything !). Title: Vendo 63 cooling system schematic Post by: Jim on August 02, 2005, 10:58:43 pm Tomorrow, I'll rummage through some manuals to see what I can come up with... Does the refrigeration plate have an ID tag that you can reference...? Perhaps a photo of the unit can shed a little light. Title: Vendo 63 cooling system schematic Post by: on August 05, 2005, 12:19:38 am Thanks for the welcome! The plate on the side of the machine says VT25 for the refrigeration unit. I will try and get a picture of the unit tomorrow. Thanks for you help! Robert Title: Vendo 63 cooling system schematic Post by: Jim on August 05, 2005, 08:43:55 am Robert, I haven't had an opportunity to check my manuals... I'll look over this weekend. Title: Vendo 63 cooling system schematic Post by: johnieG on August 05, 2005, 05:30:06 pm Here's a generic wiring diagram to get you started...hope it helps. Title: Vendo 63 cooling system schematic Post by: Jim on August 10, 2005, 09:47:53 am Unfortunately, I don't have any documention on the VT-25 refrigeration system, but as Johnie has stated, his diagram should get the unit running... Title: Vendo 63 cooling system schematic Post by: on August 12, 2005, 03:10:18 am Hey Thanks for your help, I will have to crack her open this weekend and give it a try! Robert Title: Vendo 63 cooling system schematic Post by: BryanH on August 12, 2005, 01:43:53 pm Robert... if you want the diagram for your machine, you can buy them from Funtronics as tags that were tied to the compressor.  They're about $5. Title: Vendo 63 cooling system schematic Post by: on February 11, 2006, 10:12:07 pm Hey Guys thanks for all the help! I have finally gotten a chance to mess with this thing again. I've been using johnieG's schematice, and have been tracing the rotted wiring thats left in the machine. So I modified his schematic to show what I have, because its slightly different, and I wanted to check the connection I was gonna make was right first. ON the relay there are there terminals 2 that connect to posts on the side of the compressor, and one that does connect to anything currently. Is this where the hot wire from the thermostat connects? Also the overload breaker is hooked to another seperate post is this configuration correct? Thanks for all your help guys! Robert Title: Vendo 63 cooling system schematic Post by: Creighton on February 11, 2006, 10:48:48 pm Can't help but just wanted to say nice drawing and welcome to the board!! Creighton Title: Vendo 63 cooling system schematic Post by: on February 20, 2006, 08:54:23 pm Thanks for the welcome! Wish I could take credit for the drawing. I just editted johnieG's. Thanks Robert Title: Vendo 63 cooling system schematic Post by: sodaworks on February 20, 2006, 10:23:23 pm Welcome aboard giftedone   Powered by SMF 1.1.15 | SMF © 2011, Simple Machines