Title: Variprice by vendo
Post by: ussexplorer on July 13, 2005, 02:35:41 am
Got a variprice (91E9302B-3703). Set for .25 cents no change Gives nickels and dimes for change. Has wires you move up and down to change the price from 5-.25. I rember it won't got up to 50cents. But it works just fine. Missing the sluge rejector though. If somebody could point me to a manual for setting price. I would appriciate it.
later,
Josh
later,
Josh
Title: Variprice by vendo
Post by: 90grad on July 13, 2005, 05:29:19 am
Josh,
I've got a Vari-Price on my can machine and was wondering the same thing. Here is a photo. I haven't inquired yet, but Funtronics may sell a manual for $10. Is this what you have?
I've got a Vari-Price on my can machine and was wondering the same thing. Here is a photo. I haven't inquired yet, but Funtronics may sell a manual for $10. Is this what you have?
Title: Variprice by vendo
Post by: ussexplorer on July 13, 2005, 05:37:21 am
Yea that is it. years ago I played with it. Was never able to get it above like 35 cents or something. Thus, I purchased a used coinco 9800B. The note on it from years ago was 25c no change. I remeber getting it set lower than 25c. I was wondering if it needed a conversion or something like some of the other all metal coinco mechs. Unlike the newer plastic ones with dip switches.
later,
Josh
later,
Josh
Title: Variprice by vendo
Post by: dr galaga on July 13, 2005, 10:27:56 am
I asked the same question a year ago and here is the reply that I got from johnieG:
Good luck guys!
| Quote |
| Can you just plug it in & drop in Nickles until it vends? that would verify the current setting & you should be able to then move the jumpers up/down a notch & see which way it goes.... ( PS: I hate this type of mech., they're always burned out, or just plain busted ) |
Good luck guys!
Title: Variprice by vendo
Post by: 90grad on August 05, 2005, 04:14:06 pm
I got a manual for this thing from Funtronics. I haven't read it closely, but it does tell you how to change the price.
Title: Variprice by vendo
Post by: johnieG on August 05, 2005, 05:33:35 pm
Do tell! care to share? this mech. can be quite a pill to set the pricing on... 
Title: Variprice by vendo
Post by: 90grad on August 05, 2005, 06:55:37 pm
Sure, I'll share (no offense to Funtronics, as I don't wanna cut them out of any $$). Give me some time to figure it out and I will clue you in. I am on vacation this week and have been doing some painting of the VMC can machine.
Title: Variprice by vendo
Post by: 90grad on August 08, 2005, 07:21:56 am
I have the pages in the manual that talk about setting the price on the single- and dual-price changers. I haven't played with this yet, so I can't explain any specifics. I have the whole manual, so let me know if there are any other questions. So far, I haven't seen anything else in there talking about setting the price.
The file is too large to post, so if you wanna PM me with your email address, I will send it. I have this in Adobe Acrobat, which is free to download from the net.
The file is too large to post, so if you wanna PM me with your email address, I will send it. I have this in Adobe Acrobat, which is free to download from the net.
Title: Variprice by vendo
Post by: dr galaga on August 08, 2005, 12:04:39 pm
Here you go boys and girls:
Sorry, that's as big as the forum will let me make it. Click the button to the left of the >> button to view it full size.
Sorry, that's as big as the forum will let me make it. Click the button to the left of the >> button to view it full size.