|
Title: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: Jonathan816 on December 27, 2013, 11:51:36 am I have a great coin mech, however it came out of a Westinghouse. I'd like to swap out the rear shaft/ rod, however unsure as to where I can get it from. I guess if I can't find it I can always make this one work.
(http://i1051.photobucket.com/albums/s438/Jonathan816/IMG_20131227_114657_zps796b4e1e.jpg) (http://s1051.photobucket.com/user/Jonathan816/media/IMG_20131227_114657_zps796b4e1e.jpg.html)(http://i1051.photobucket.com/albums/s438/Jonathan816/IMG_20131227_114643_zps5de9f7ca.jpg) (http://s1051.photobucket.com/user/Jonathan816/media/IMG_20131227_114643_zps5de9f7ca.jpg.html)(http://i1051.photobucket.com/albums/s438/Jonathan816/IMG_20131227_113850_zpsf0310974.jpg) (http://s1051.photobucket.com/user/Jonathan816/media/IMG_20131227_113850_zpsf0310974.jpg.html) Title: Re: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: Ltransam on December 27, 2013, 12:21:57 pm Tom will be able to help on this !!! I'm not sure but I think you just have to relocate the hole 90degrees but again Toms the expert :smile: Title: Re: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: Slapshot42 on December 27, 2013, 12:50:38 pm I had one converted last Spring by Tom. Works great. I believe the shaft rod is too long and has to be cut down? Been awhile but I know it can be converted to work on a Vendo.
Title: Re: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: Jonathan816 on December 27, 2013, 01:13:59 pm I had one converted last Spring by Tom. Works great. I believe the shaft rod is too long and has to be cut down? Been awhile but I know it can be converted to work on a Vendo. Do you recall what tom charged?Title: Re: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: Slapshot42 on December 27, 2013, 01:21:50 pm Do you recall what tom charged? No. I would reccomend you send it out to him have it evaluated. He will tell you exactly what it needs to work,etc. Never had a problem. Tom is honest, and reliable...you should have no problems! Title: Re: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: Ltransam on December 27, 2013, 01:35:09 pm Yep again Toms the man !!!
I just sent him a couple change givers Mechs to adjust & Clean for me :tounge: Title: Re: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: Jonathan816 on December 27, 2013, 04:29:54 pm Sounds like I need to wait for Tom to reach out then and provide some insight.
Thanks everyone. Title: Re: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: collecture on December 27, 2013, 07:13:17 pm Jonathon,
The shaft is the same length, but the pin hole is smaller and on the horizontal. You will need to drill a 1/8" hole O.C. - 1/4" from the end of the shaft O.C. The other difference between the mechs is the Sold Out Flag. The Westy mech doesn't have the extension needed to actuate the SO Flag. PM me if you need more help. Title: Re: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: Ltransam on December 27, 2013, 08:45:51 pm SEE :tounge: Toms the MAN !!!!! Title: Re: WTB Coin Mech Post for VMC/VENDO 110 Change giver Post by: Jonathan816 on December 28, 2013, 08:49:31 am Jonathon, The shaft is the same length, but the pin hole is smaller and on the horizontal. You will need to drill a 1/8" hole O.C. - 1/4" from the end of the shaft O.C. The other difference between the mechs is the Sold Out Flag. The Westy mech doesn't have the extension needed to actuate the SO Flag. PM me if you need more help. Thanks - sounds like I need to find a machine shop that will do the drilling as I don't have a drill press. Thank you very much everyone. |