SMC Discussion Areas

Soda Machines, Coolers & Dispensers => Pre 60's Machines & Coolers => Topic started by: stburger on May 15, 2010, 04:24:43 pm



Title: Vendo 81 question
Post by: stburger on May 15, 2010, 04:24:43 pm
Looking for help. I need quidance on replacing new breaker strips and gasket on cabinet.Machine is not disassembled.  Also I am replacing the adjustable legs, and the back right corner one snapped off . It's is almost impossible for me to get to it from the inside with the compreser in the way. thoughts please . Thanks Steve


Title: Re: Vendo 81 question
Post by: collecture on May 15, 2010, 06:06:46 pm
To remove the feet, you have to lay it down and spray each leveler with something like PB Blaster. Let it rest a bit, tap each foot with a hammer and spray again. After a little while, get a blow torch and heat each leg up and then they will come off easily. If you just try to unscrew them, 90% of them will snap off!
To get the broken one out, you will probably have to remove the compressor assembly. Look first and see whether there is enough of the leg bolt sticking up to get a grip on and again follow the PB Blaster/torch instructions. If there is not enough to grab, don't waste your time removing the compressor yet as you are stuck drilling it out.
Worst case scenario replace the threaded insert - Fun-Tronics sells it. You will have to remove the compressor for this.
http://www.fun-tronicsllc.com/store.php?crn=254&rn=454&action=show_detail

The breaker strips simply push in towards the cabinet and then they can clear the clips on the liner.


Title: Re: Vendo 81 question
Post by: loman4ec on May 15, 2010, 06:51:54 pm
Also if you cannot get the leg leveler out you can use bolt extractors. They look like drill bits. You drill a hole in the center of the leveler and use the extractor and it will grip the screw. I would first use PB Blaster and then heat it like Collecture suggested.


Title: Re: Vendo 81 question
Post by: stburger on May 15, 2010, 07:55:35 pm
Thanks Guys, I still have a question on the breaker strips. The left one along the bottle gate looks complicated.It seems to be tucked in behind it. No sure what to do.


Title: Re: Vendo 81 question
Post by: SIGNGUY on May 15, 2010, 08:18:46 pm
Are you restoring this machine? if so I'm assuming your taking it all apart? correct/

the bottle stock needs to be removed to get that left one off and new one on..



Title: Re: Vendo 81 question
Post by: stburger on May 17, 2010, 12:14:51 pm
No, what I need is to replace seal that is goes on the strips, order the breaker strips and seal  from Rod at Funtronics


Title: Re: Vendo 81 question
Post by: SIGNGUY on May 17, 2010, 03:35:28 pm
You'll have to remove the bottle stack to get to the breaker strips..

it's easy, remove the shelves
Remove the screws holding the bottle stack to the cabinet and while taking the last one off, The last one on the top, hold the stack or have someone help you as it's a little heavy, and it will come right off... easy to put back on by reversing this order.

Good luck!


Title: Re: Vendo 81 question
Post by: stburger on May 17, 2010, 05:23:31 pm
I will give it a shot. Also is there an easy way to clean up shelves, steel wool ?? They don't need to look brand new, I have repaced all the springs, just want them to look cleaner.Thanks Steve                                                 


Title: Re: Vendo 81 question
Post by: coke_and_stuff on May 17, 2010, 06:24:51 pm
simple green and a Scotch Brite pad

Joey