SMC Discussion Areas

The Vending Rack => Swap Meet Area => Topic started by: 90grad on June 20, 2006, 05:49:29 am



Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 05:49:29 am
All,

Here is the first of a few messages with the photos of the Vendo 23 parts I am selling.  I have no idea on prices, so make me an offer.  If no one here wants something, it's going on GreedBay.

I have other small items, so if you don't see something, just ask.  I have some body pieces.  The top and disk I have are in pretty decent shape with a some surface rust on the disk.  I do have a bottle door, but no hinge pin or spring.

This post has two photos of the bottle basket.  You can see it is in very good shape and just needs a good cleaning.  There is some surface rust on the brackets underneath, but there is no real structual damage.






Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 05:52:48 am
Here is the coin entry plate WITH the sold out window.  The window is not attached, so I could sell this separately.  I think the window sells for $12 from Funtronics.  It has some discoloration around the edges where the glue was, but the center is in good shape.


Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 05:53:43 am
Here is the drain channel.  It has some pitting.


Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 05:56:08 am
Here is the COMPLETE evaporator coil and capillary tube.  I spoke with Eric at Global and said this just needs to be mated to a lower end assembly.  I was careful not to alter the length of the cap tube, as that would affect the system.  The line was cut right at the compressor.  This has been kept in a dehumidified room with aluminum tape over the open ends.


Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 05:57:07 am
Here is the service manual.  I ordered this off the net and can send either this one or a .pdf file.


Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 05:59:08 am
Here is the coin mech WITH the sold out flag.  I could not find the coin return rod, but I will keep looking.  I tested this the other day with a dime slug rejector and it worked properly.  There is some surface rust, but this should clean up nicely.  The star handle has a fair amount of pitting in the chrome.

UPDATE: This has been sold to GMiller.






Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 06:01:10 am
Here is the tank for the bottle basket.  It does have some surface rust, but is mainly dirty.  I didn't have time last night to clean it up before taking pictures.


Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 06:02:52 am
Here is the trim for the bottle opener and coin return cup.  I have an extra bottle opener trim.  These are in pretty good shape.





Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 09:41:40 am
Here is the bottle door.  It doesn't have a pin, spring or gasket.  The paint on top is dulled.  There is a very small amount of surface rust on the handle and hinges.  Overall, it's in excellent shape - very straight.

UPDATE: This is has been sold to Ltransam.






Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 09:44:00 am
Here is the top and spin disk.  However, I will separate these if some one desires.  Both are very straight.  The top has very little surface rust and the disk has a lot of surface rust underneath.  Nothing is through.

I also have the cover that goes on the underside.  That will be posted in the next reply.






Title: Vendo 23 parts sale
Post by: 90grad on June 20, 2006, 09:46:54 am
Here is the cover plate that goes underneath the top.  For some reason, it was painted white.  There is some surface rust on the top and bottom.  However, it is straight and no rust is through.

I think this may be all I have to sell.  I do have a front door.  It is the solid style (the shelf is one solid piece).