SMC Discussion Areas
May 06, 2024, 12:22:54 am *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: 1 2 3 4 [5] 6 7 8 9 10
 41 
 on: February 10, 2024, 07:15:49 am 
Started by Manu - Last post by Jim
I may have one in PDF format; I'll check and get back to you this evening...

 42 
 on: February 08, 2024, 12:10:19 pm 
Started by Manu - Last post by Manu
Hi guys, i`m looking for a Vendo Coin Changer service manual.
I know some places that sells them printed, but as i am not from the Us i was want to find someone that sells digitally.
Any advise where to find one will be apreciated.

 43 
 on: February 05, 2024, 09:26:23 am 
Started by chuggybear - Last post by Zerbie
So true....I use this forum quite often for help.

 44 
 on: February 05, 2024, 09:24:16 am 
Started by Pope - Last post by Zerbie
Looks like a very nice Machine! Congrats!

 45 
 on: February 04, 2024, 01:07:45 pm 
Started by FlightTest - Last post by johnieG
I'm happy you got it up & running again...well done!   drinking

 46 
 on: February 03, 2024, 06:57:49 pm 
Started by FlightTest - Last post by FlightTest
Putting in the new fan that directs airflow in the right direction made for a huge improvement.  I did have to work with the new fan blade quite a bit because it was pretty far out of balance.  I worked on trimming the blade pitch to make sure all of the blades were positioned the same.   However it still shook like crazy where the old fan blade was smooth.  I put a clip on one blade at a time until it started to run smooth. Then once I found the blade that needed weight I drilled a small hole in it about mid point and put in a very small screw.  At first it still had a small wobble so I kept filing away at the screw end until it finally ran nice and smooth.   

The new blade made the Temps way more even in such a tall machine.   I am still working on getting the thermostat set right.  Currently it shuts off around 27 degrees and turns on at 35 with the temp sensor about 12 inches above the bottom of the machine.  I put several water bottles in it at different heights and the bottom ones seem to average around 33 to 34.  And the tops are around 35 to 36.  So I think that's getting close to where I want it.   

It's nice to have it up and working.   Now I need to go get some bottles to try it out for real!

Thanks again for all of your guidance.

 47 
 on: February 01, 2024, 07:27:36 pm 
Started by Pope - Last post by johnieG
Nice find!

 48 
 on: January 31, 2024, 11:18:15 pm 
Started by Pope - Last post by Pope
More like welcome back...

Been a member for 10 years just been away for a while.

 49 
 on: January 31, 2024, 10:10:35 pm 
Started by Pope - Last post by Ltransam

Great score ! Welcome to the Club

 50 
 on: January 31, 2024, 10:25:14 am 
Started by Pope - Last post by Jim
Very Nice ! ! !  Congrats on the new addition!

Pages: 1 2 3 4 [5] 6 7 8 9 10
Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!