|
audiobeer
|
 |
« on: December 13, 2005, 09:52:21 pm » |
|
OK, I got the cooling fixed. New Compressor, and both fan motors. It cycles on at 40 and off at 30 degrees. Thelids fit on ok but if you nudge it wrong it slides off. There is something missing but what? Here's a pick of the cooler lid open on one side. Is ther some gaskets missing? Here's the one left over piece on top of the lid. I'm assuming that rests on top of the circulating fan cage......is it missing some rubber?
|
|
|
|
|
Logged
|
Missouri
|
|
|
|
audiobeer
|
|
« Reply #1 on: December 13, 2005, 09:55:07 pm » |
|
Here's a pic of the dug out are the lids sit on top of the outer edges. Excuse the interior. That's the last thing I have to do.
|
|
|
|
|
Logged
|
Missouri
|
|
|
|
audiobeer
|
|
« Reply #2 on: December 13, 2005, 09:58:00 pm » |
|
Here's a pic of the outside. This was on Ebay for a ridiculous amount. Nobody bought it. Every few weeks it would come back on Ebay with the reserve going down another few hundred dollars. After the 4th or 5th time with to high a reserve I emailed and finaly got it cheap when the husband was deer hunting? The wife emailed me and made me an offer I couldn't refuse but had to come and get it NOW! 
|
|
|
|
|
Logged
|
Missouri
|
|
|
|
Jim
|
|
« Reply #3 on: December 14, 2005, 08:05:16 am » |
|
That looks like a WD-10...
I think there should be some sort of gasket along the lid to seal the compartment and stop the lid from sliding around the top edge of the cooler... I think I have reference material that I look at for the answer. Check back later today...
I also think the trim piece along the bottom front should be polished, not painted red.
|
|
|
|
|
Logged
|
My six cents, Jim  |
|
|
|
audiobeer
|
|
« Reply #4 on: December 14, 2005, 08:59:57 am » |
|
Thanks Jim. Appreciate any help. Actualy there is no trim on the bottom, cannot locat that piece?
|
|
|
|
|
Logged
|
Missouri
|
|
|
|
johnieG
|
|
« Reply #5 on: December 14, 2005, 09:41:32 am » |
|
The lids on the WD10 should have a squarish-fiberglass inner liner (one per lid) that holds some insulation to keep the cold from migrating into the bottom of the lids, this is what keeps the lids centered on the top,Jim is also correct that there should be a gasket on the outer-edge of the lids too.
|
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
audiobeer
|
|
« Reply #6 on: December 14, 2005, 10:43:43 am » |
|
Steve Ebners shipping some preforms to me. We'll see what happens. Again Thanks!
|
|
|
|
|
Logged
|
Missouri
|
|
|
|
coke_and_stuff
|
|
« Reply #7 on: December 14, 2005, 08:04:08 pm » |
|
what year VW convert or hardtop? looks like a nice car is it yours?
Joey
|
|
|
|
|
Logged
|
Collector of nice original paint machines
Vendo 81 B, C, D
VMC 81 Pepsi, 7up, RC, Generic
6CV Coke, RC, Pepsi
VMC 110 RC
Vendo 39
Jacobs 26
Mills 47
Selectivend 64 7up NOS
Plus 30-50 parts and project machines
|
|
|
|
Jim
|
|
« Reply #8 on: December 14, 2005, 09:52:12 pm » |
|
Here's a diagram from the service manual for the WD-5, WD-10, WD-12 & WD-22. It shows that there's supposed to be a gasket on the cooler as well as one along the center which is the piece you have pictured on one of the lids.
|
|
|
|
|
Logged
|
My six cents, Jim |
|
|
|
audiobeer
|
|
« Reply #9 on: December 14, 2005, 11:08:02 pm » |
|
Nice job Jim! I have some of the inserts coming and am cutious as to how they will be affixed to the Lid. Do you think I will have to drill out all the rivets you see in the lid pic I have? Another wuestion comes up is how was thtat center stripped secured? Thanks again folks!
|
|
|
|
|
Logged
|
Missouri
|
|
|
|
