|
Guest
|
 |
« Reply #20 on: August 05, 2005, 12:12:23 am » |
|
O.k., so now I have finally gotten around to digging around in my V-110 that I bought and put in my garage several months ago. I am probably going to replace my V-216MD in the kitchen with the V-110 since the 216 only offers 3 selections whereas the V-110 has 10 selections.
So, while looking it over inside, I saw two things that stood out. I need all of your help on them...
First I saw this tiny switch just above the glass bottle door on the inside surface of the large door. The vending is mechanical of course and I can't figure out what this switch does. Please set me straight. See below:
|
|
|
|
|
Logged
|
|
|
|
|
Guest
|
|
« Reply #21 on: August 05, 2005, 12:18:28 am » |
|
Also, everything looked fine in the bottom compartment (except for a TON of dust), but one thing troubles me...
All the wires go to and from the junction box, but there is one wire/cord coming from it that is cut off. What is that cord for?
It may be too hard for you to know from the bad photo, but please give it a try.
Thanks so much,
~Markito
|
|
|
|
|
Logged
|
|
|
|
|
|
|
Bob K
|
|
« Reply #23 on: August 05, 2005, 06:55:32 am » |
|
Kito, the switch is for the bottle door light. When I power up my 81, I have to reach in and hold that switch for the bottle door light to come on. Your 110 does have the fluorescent tube on the side of the bottle door, correct?
Bob
|
|
|
|
|
Logged
|
|
|
|
|
Guest
|
|
« Reply #24 on: August 05, 2005, 09:06:39 am » |
|
Wow! Yes it does! The bulb was burnt out and I was standing to the left when I opened the bottle door, so I had no idea there was a panel with the bulb there. I'm used to squaretops, so I did look for a nightlight bulb at the top, but I never thought to look along the side.
I wonder if the cord to power he bulb is the one that is cut? Is the cord to the light visible on the V-110?
Thanks so much!
By the way, here's my machine. It is near perfect except for a tiny hole on the face (what a shame).
And by the way, those are soft moving blankets on top of the machine, not shards of glass and razor-wire. 
~Markito
|
|
|
|
|
Logged
|
|
|
|
|
Eric
|
|
« Reply #25 on: August 05, 2005, 09:43:20 am » |
|
Nice machine! You could have that hole fixed and the paint blended then you'd never know.
Or a well placed decal could do the trick too!
Eric
|
|
|
|
|
Logged
|
Eric
WANTED:
Embossed Quikold Standard
|
|
|
|
loman4ec
|
|
« Reply #26 on: August 05, 2005, 10:02:03 am » |
|
Here is an idea for the wiring. Could it possibly been rewired at sometime. I was thinking that it could be the wire that would supply power to the coin mech but since this is a manual machine the technition just cut it off?
|
|
|
|
|
Logged
|
|
|
|
|
Eric
|
|
« Reply #27 on: August 05, 2005, 10:43:57 am » |
|
I don't know if this would help at all.... it's a wiring diagram for a 81....
Don't know how much different a 110 set up is.... but maybe you can figure it out...
|
|
|
|
|
Logged
|
Eric
WANTED:
Embossed Quikold Standard
|
|
|
|
Eric
|
|
« Reply #28 on: August 05, 2005, 10:47:19 am » |
|
Here's the text page...
|
|
|
|
|
Logged
|
Eric
WANTED:
Embossed Quikold Standard
|
|
|
|
MoonDawg
|
|
« Reply #29 on: August 05, 2005, 10:55:18 am » |
|
Just below the light fixture in the door is a hole where the power cord is led. If anyone needed to remove the door they would need to cut it's power cord. Strongly suspect the cut wire is meant for the light.
|
|
|
|
|
Logged
|
Glen
|
|
|
|
