|
coke_and_stuff
|
 |
« Reply #30 on: August 23, 2013, 06:13:35 pm » |
|
I may have you one as well. I dug through a few parts bins looking for something and found a few misc bezels. I need a pic as well.
Thanks,
Joey
|
|
|
|
|
Logged
|
Collector of nice original paint machines
Vendo 81 B, C, D
VMC 81 Pepsi, 7up, RC, Generic
6CV Coke, RC, Pepsi
VMC 110 RC
Vendo 39
Jacobs 26
Mills 47
Selectivend 64 7up NOS
Plus 30-50 parts and project machines
|
|
|
|
Rebel
|
|
« Reply #31 on: August 23, 2013, 08:49:27 pm » |
|
I may have you one as well. I dug through a few parts bins looking for something and found a few misc bezels. I need a pic as well.
Thanks,
Joey
Joey,,you need a pic of what one looks like,,is that correct ? |
|
|
|
|
Logged
|
|
|
|
|
|
|
coke_and_stuff
|
|
« Reply #33 on: August 23, 2013, 09:22:31 pm » |
|
I have one that you described with the words opener stamped in the top. BUT my inside measurements measure 2 inches wide and 3 1/4 tall on the inside measurements. The bezel is larger, are you measuring the hole on your coin door for your measurements?
Thanks,
Joey
|
|
|
|
|
Logged
|
Collector of nice original paint machines
Vendo 81 B, C, D
VMC 81 Pepsi, 7up, RC, Generic
6CV Coke, RC, Pepsi
VMC 110 RC
Vendo 39
Jacobs 26
Mills 47
Selectivend 64 7up NOS
Plus 30-50 parts and project machines
|
|
|
|
MoonDawg
|
|
« Reply #34 on: August 23, 2013, 09:24:56 pm » |
|
The machine on E-bay is an early model 63, that bezel will not fit your late model 63.
|
|
|
|
« Last Edit: August 23, 2013, 09:29:13 pm by MoonDawg »
|
Logged
|
Glen
|
|
|
|
Rebel
|
|
« Reply #35 on: August 23, 2013, 09:28:28 pm » |
|
I have one that you described with the words opener stamped in the top. BUT my inside measurements measure 2 inches wide and 3 1/4 tall on the inside measurements. The bezel is larger, are you measuring the hole on your coin door for your measurements?
Thanks,
Joey
I am measuring the opening in coin door. That measurement you have would be correct if you're measuring the opening if you were looking at it INSTALLED. That inside measurement you got would be on the very edge of coin door opening if installed. Got to be correct one I'd think. |
|
|
|
« Last Edit: August 23, 2013, 09:32:46 pm by Rebel »
|
Logged
|
|
|
|
|
Rebel
|
|
« Reply #36 on: August 23, 2013, 09:37:36 pm » |
|
The machine on E-bay is an early model 63, that bezel will not fit your late model 63.
Moondawg, Think you are right but the design is correct I think. Joey's measurement of bezel opening I think would be the correct one as that measurement of bezel edge would be almost exactly where it would fit in coin door hole.
Joey,,can you shoot me a pic of what you found ?
|
|
|
|
« Last Edit: August 23, 2013, 09:45:35 pm by Rebel »
|
Logged
|
|
|
|
|
coke_and_stuff
|
|
« Reply #37 on: August 23, 2013, 09:48:43 pm » |
|
Sent you an email with a pic.
Thanks!
Joey
|
|
|
|
|
Logged
|
Collector of nice original paint machines
Vendo 81 B, C, D
VMC 81 Pepsi, 7up, RC, Generic
6CV Coke, RC, Pepsi
VMC 110 RC
Vendo 39
Jacobs 26
Mills 47
Selectivend 64 7up NOS
Plus 30-50 parts and project machines
|
|
|
|
Rebel
|
|
« Reply #38 on: August 24, 2013, 10:50:08 am » |
|
Did ye get my last email last night Joey asking if you had Paypal ??
|
|
|
|
|
Logged
|
|
|
|
|
Rebel
|
|
« Reply #39 on: August 25, 2013, 09:18:45 pm » |
|
Green neon and green LED's should be in tomorrow. Have all the wiring done and lower comp. area painted and waiting. Had to go with LED'S inside as the neon puts off way to much heat and is 110v,,the green neon that will go under machine is 12v so ran a power strip in lower comp. compartment with a 12v convertor and will plug 110v LED's in power strip.
Thanks to Joey,,,have a opener bezel coming in from him and it was a pleasure doing biz with him. Thanks Joey.
|
|
|
|
|
Logged
|
|
|
|
|
