Compressor problems

[ck]

I restored an Ideal 400 Slider replacing the old compressor with one from Global compressors The refrigeration guy recharged it and connected the T stat At first it would cool down but would not shut off Now he replaced the T stat , still cools down but it will now shut off only when I turn the setting down I though this guy with 32 years experience was suitable but now I have doubts Any suggestions greatly appreciated

[kbareit]

Did you contact your service guy and tell him about the problem? It might be the new t-stat is bad. Sometimes you get a new one that is bad.

[msanborn]

Global has always been top notch, and has been great to work with, I would start there, Eric is a great guy, always helps when I call him with questions. 

[ck]

I have replaced the T stat and I send an email to Eric 2 weeks ago long with pictures and no response yet I am very disappointed with him

[collecture]

ckuruliak -
Are you saying you had another tech charge the system and install the T-stat after Eric returned the system to you?
What type T-stat does the 400 use? Is it a contact style T-stat? Pictures will help...

[ck]

here is some pictures and yes a tech charged he system after Eric send me the new compressor

[ck]

here is the picture of the old compressor

[globalcompressors]

ckuruliak -
Are you saying you had another tech charge the system and install the T-stat after Eric returned the system to you?
What type T-stat does the 400 use? Is it a contact style T-stat? Pictures will help...

that's right Tom. I sold the man a new lower unit for the Ideal, on the premise of him having a
qualified, certified technician, to install it and charge it up.

[ck]

thanks Eric but  I did not smear your name Had you responded to my email 2 weeks ago I would not have to post my problem in here  All I want was a response to my question and you never gave it until now I was not asking for much at all just a little help

[msanborn]

Eric is very busy, just keep trying, he will eventually get back to you.  I had identical problem, what he is telling you is correct.  Good luck. 

[ck]

Well Eric I do not feel like arguing in public but I feel the need to respond. First I am 2000 miles from you ,do you really think I should ship my machine out to you have you install the compressor  then have you ship it back to me? Come on be reasonable!!!! Since you are a businessman, I feel the proper edict is to respond to a customer's complaint for help positively or negatively, You chose to do neither and  I was disappointed by your lack of response.  If that is calling you out then I am guilty .Isn't business all about 'customer service? Your ranting does nothing to help this situation, only shows your true colours Enough said!!! please refrain from commenting  unless you want to give any other additional constructive advice other than what you have offered which I appreciate!!!!!

[MoonDawg]

       CK, it sounds like your compressor is working just fine and your refrigeration guy has charged it properly although that drier does not look like it is strapped to anything.

       The problem narrows down to the thermostat's capillary tube not sensing the temperature properly and as Eric mentioned, it may be because you now have a different style with lot shorter probe than the old one, and was made to go inside the cooling compartment.
 Did you order the t/s for a slider?

       If it was reccomended for your machine, did you coil the new cap tube before sliding it in place? Also I have had sliders where the pipe that the cap tube slides into, has broken loose and not even made contact with the inner linner.

        Start by dipping the sensor into a cup of ice to see if it will shut off. If so, then back up the tube again and if still no luck there......lead either the cap tube or the whole t/s directly into the box and make a direct contact with the wall.

        Let us know how it works out 

[ck]

thanks MoonDawg I will do that. This is my first time restoring a soda machine so I am learning as I go. I am trying to get an idea on how it should work by asking for advice in here before I go back to my service guy or he will just feed me another line of BS and send me on my way. Obvious I got the wrong guy!!! The T/S was supplied by Eric so I assume it is the right one I think what you said makes a lot of sense so I have to start somewhere  Thanks again