|
Husker
Guest
|
 |
« on: December 02, 2009, 02:21:34 am » |
|
Hello all..me again.. with another noob question .... or 5.. Choicevend 168; Coinco S759800B; which the coin changer is not working nor will it vend.. (I found the op and service manual per one of you great people out there) I have read it.. and reread it..
To my question..When i drop $$ in, it goes straight to the change bucket, all change.. but DONT vend. (This is for home use/ but would be nice if the changer did work..) I have heard that the boards on the coin changers go bad; but is their a way to "bypass" the unit to see if it will vend?..(Wire it for Free Play??..) the augers work when i hit the lil rod underneath.. and i can hear the relay box "clicking"... but i dont know my next step should be... check coin changer?.. or other problems..
Also the Jones Connector; anyone tell me what the wiring is?.. i found 115 volts of power, but no other power.. i dont know what the other 5 wires are....
I hope this isnt posted in the wrong section.. You guys are a HUGE help.. Thanks again.... From: Your learning Noob... lol
|
|
|
|
« Last Edit: December 02, 2009, 02:32:33 am by Husker »
|
Logged
|
|
|
|
|
|
|
bubba
|
|
« Reply #2 on: December 02, 2009, 07:30:03 am » |
|
Make sure the machine has product in it or it will bypass all the coins.
|
|
|
|
|
Logged
|
Ken
V-63 -Bottles
2-Cavalier USS-64
VMC ST56B Royal Crown - being built
Vendo HA56C Coke
2-V63C DP
V63C Coke
U-Select-It 5cent candybar machine
|
|
|
|
Husker
Guest
|
|
« Reply #3 on: December 02, 2009, 04:23:09 pm » |
|
Yes; at least 1/2 full all slots.. and its even down thru the augers..
|
|
|
|
|
Logged
|
|
|
|
|
johnieG
|
|
« Reply #4 on: December 02, 2009, 09:27:45 pm » |
|
Make sure the machine has product in it or it will bypass all the coins.
A choice-vends' auger system does use an "empty" switch that that will lock out that particular columns selection button, but it won't prevent the coinmech from accepting coins like in a Vendo with a serpentine rack delivery gate system. jumper pins 1 to 3 on the female "jones" socket with the coinmech removed/unplugged, & see if it will set the vending/credit relay & allow you to vend a selection. |
|
|
|
|
Logged
|
Spoon-feeding Newbies since 2001...  Yeah..220,221 whatever it takes. Remember, all it needs is a shot of Freon! The Vendo V-83 is the '59 Edsel of the coke machine world. ;p Spray painting does NOT restore a compressor 11 is louder than 10... "Hope" is good, but it's not an action plan. |
|
|
|
Husker
Guest
|
|
« Reply #5 on: December 03, 2009, 04:21:46 pm » |
|
ok.. i jumped 1 and 3.. i heard a single "click"; no vend ( i also checked on the relay box to see if it tripped something... it didnt)... i thought i read that i have to tie in #7 also?...
|
|
|
|
|
Logged
|
|
|
|
|
pepsi-perk
|
|
« Reply #6 on: December 03, 2009, 05:52:06 pm » |
|
Have the power OFF to the machine.
Put 2 wires in #1 - take the other end of one of the wires and put it in #7. Leave the other wire hanging for a minute.
Now, take another wire and put it in #3.
Turn power ON.
Now take the loose wire that you have hanging out of # 1 and touch it for just a second or two to the other wire hanging out of #3.
This will trigger for a vend - make your selection and see if it works. GOOD LUCK!
|
|
|
|
|
Logged
|
|
|
|
|
Husker
Guest
|
|
« Reply #7 on: December 03, 2009, 06:24:32 pm » |
|
YES!!!!.. Thank You very much Pepsi Perk!!!!! Now just install a momentary microswitch and im set? Thank you again very much.. i was so lost.. You guys are the BEST!!...  |
|
|
|
|
Logged
|
|
|
|
|
Husker
Guest
|
|
« Reply #8 on: December 03, 2009, 06:28:44 pm » |
|
So shall i assume that the coin mech is junk then ?
|
|
|
|
|
Logged
|
|
|
|
|
pepsi-perk
|
|
« Reply #9 on: December 03, 2009, 06:31:06 pm » |
|
Yep...just solder those two wires to a switch...get one rated for 125V AC at Radio Shack or some hardware store.
Make sure it is a NORMALLY OPEN switch - so when you push the button you will be shorting out those two wires like you just did when you touched them together.
Hide the switch somewhere and enjoy!
CHEERS!
|
|
|
|
|
Logged
|
|
|
|
|
Husker
Guest
|
|
« Reply #10 on: December 03, 2009, 06:35:50 pm » |
|
Totally AWESOME!!!.. You guys rule..
I checked all the buttons.. the double dispenser (the one to my far right) isnt dispensing.. i can move it manually from the underside switch; but wont dispense on its own...the rod to move it IS a lil stiff..
take it apart and clean it up??!..
|
|
|
|
|
Logged
|
|
|
|
|
pepsi-perk
|
|
« Reply #11 on: December 03, 2009, 06:47:18 pm » |
|
I would have to say yes on the coin mech being messed up...but that is a Johnie G question....I am still a newbie myself. You can get coin mechs on ebay cheap. Just have to hunt around a jump on one. Good Luck.
|
|
|
|
|
Logged
|
|
|
|
|
Pat Pixley
Guest
|
|
« Reply #12 on: December 04, 2009, 12:56:53 am » |
|
The Coin mech. you will want to keep the slug rejector. you may come acrossa mech down the road.
|
|
|
|
|
Logged
|
|
|
|
|
