Menu Content/Inhalt
SMC Discussion Areas
December 02, 2008, 10:28:08 pm *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
News:
 
   Home   Help Login Register  
Pages: [1]   Go Down
« previous next »
  Print  
Author Topic: Drawing schematic  (Read 285 times)
0 Members and 1 Guest are viewing this topic.
Skeleton Man
Soda Jerks
*****
Offline Offline

Posts: 641


WWW
« on: May 04, 2005, 12:46:03 pm »
I'm trying to hand draw a copy of the wiring diagram from inside the coin door of my machine. It's covered in mould and grime and is falling to peices, but I can make out some details.

My problem is I'm hopeless at drawing and I can't get anything to look right..

I tried photographing the diagram, all you see is a brown and yellow patch with lines on it !  Get any closer and all you get the reflection from the camera flash..

Does anyone have any suggestions ?  I suppose I could draw up something based on the physical wiring, but it's confusing because the wiring diagram shows sold out lights, and the machine only has back lights for the buttons !

If anyone knows where I can find a schematic for my old cornelius square-top that would be even better.. but I'm doubtful... nobody appears to have even heard of my model !
Logged
dr galaga
Administrator
Soda Jerks
*****
Offline Offline

Posts: 1981


Sorry, but it's a POP MACHINE!


WWW
« Reply #1 on: May 04, 2005, 10:40:45 pm »
Quote (Skeleton Man @ May 04 2005,12:46)
Get any closer and all you get the reflection from the camera flash.

Get a trouble light and hold it (or have the gf hold it - the light that is) off at an angle and turn the flash off.
Logged
Cavalier CS-80C
Vendo 63
Westinghouse WB102-B4-D
 --------------
The ultimate glass bottle soda site: www.GlassBottleSoda.org
My gameroom: Arcade80s.net
Creighton
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 2051
« Reply #2 on: May 05, 2005, 01:13:36 am »
Last resort will be to carefully steam the remaining pieces off and reassemble on a copier or scanner and then try and connect the paths. Long shot but really have no other option that I can think of.
Best of luck!!
Creighton
Logged
Skeleton Man
Soda Jerks
*****
Offline Offline

Posts: 641


WWW
« Reply #3 on: May 05, 2005, 02:56:37 pm »
Update: I've managed to draw part of the relay/coinmech wiring.. need to look at the wiring harness to get the rest I think..

Wiring Diagram
Logged
Skeleton Man
Soda Jerks
*****
Offline Offline

Posts: 641


WWW
« Reply #4 on: May 05, 2005, 10:08:52 pm »
Question: What do you call the microswitches that tell the coin mech the machine is vending ? (ie. control the crems)
Logged
johnieG
Global Moderator
Soda Jerks
*****
Offline Offline

Posts: 2449
« Reply #5 on: May 06, 2005, 08:19:02 am »
It's sometimes refered to the "Vending"  switch, it normally is held closed ( it puts a 115 volt AC signal on pin #7 on the jones plug) to tell the coinmech/CREMS that it's ready to "vend" , then during a vending cycle, it opens, (on some coinmechs this is also refered to as the "Blocker" line)  ie: it blocks the coinmech from accepting coinage until the vending cycle is completed (you pushing the selection button, or pulling a bottle from the stack.)
Logged
Yea, 220...221, whatever it takes.
Skeleton Man
Soda Jerks
*****
Offline Offline

Posts: 641


WWW
« Reply #6 on: May 06, 2005, 01:33:42 pm »
I thought it was pin 6 ? (pin 6 is CREM, pin 7 is VEND NC)

I just needed the name for my diagram.. wasn't sure what to call those switches..  thanks '<img'>

I'm making progress with the diagram.. nearly got the vend mechanism drawn up.. (well scribbbled on scrap paper.. still gotta draw it up properly in Visio)
Logged
Pages: [1]   Go Up
  Print  
« previous next »
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.7 | SMF © 2006-2008, Simple Machines LLC
Joomla Bridge by JoomlaHacks.com 		Valid XHTML 1.0! Valid CSS!